Husqvarna AUTOMOWER 420 Guía Rápida página 3

For more information and instructions, read the complete Operator 's manual on the Husqvarna
website (w w w.husqvarna.com).
1. PL AC E M E N T O F A N D CO N N EC T I N G T H E C H A RG I N G S TAT I O N
1. Place the charging station with a lot of open space in front of the charging station and on a relatively horizontal surface.
2. Connect the power supply's low voltage cable to the charging station and the power supply.
3. Connect the power supply to a 100-240 V wall socket.
4. Place the robotic lawnmower in the charging station to charge the battery while the boundary wire is laid. Set the main switch
to position 1.
2. PL AC E M E N T O F T H E B O U N DA RY W I R E A N D T H E G U I D E W I R E
1. Lay the boundary wire so that it forms a loop around the work area.
2. Make an eyelet at the point where the guide wire will later be connected.
3. Run the guide wire to the point on the boundary loop where the connection will be made. Avoid laying the wire at tight angles.
3. CO N N EC T I N G T H E B O U N DA RY W I R E A N D T H E G U I D E W I R E
1. Narrow passages in the garden make it difficult for the robotic lawnmower to find the charging station. The robotic
lawnmower can be lead to remote garden areas using the guide wire. The guide wire also helps the robotic lawnmower to
quickly find the charging station.
2. Lay the guide wire under the charging station and at least 2 m / 6.5 ft straight out from the front edge of the charging station.
3. Open the connectors and lay the wire ends in the recesses on each connector.
4. Press the connectors together using a pair of pliers.
5. Cut off any surplus boundary wire. Cut 1-2 cm / 0.4-0.8 " above the connectors.
6. Press the boundary connectors onto the contact pins, marked AL (left) and AR (right), on the charging station. It is important
that the right-hand wire is connected to the right-hand contact pin, and the left-hand wire to the left-hand pin.
7. Fasten the guide connector to the contact pin marked G1 on the charging station.
4. CO N N EC T I N G T H E G U I D E W I R E TO T H E B O U N DA RY W I R E
1. Cut the boundary wire with a wire cutters at the centre of the eyelet that was made in step 2.2.
2. Connect the guide wire to the boundary wire using the accompanying couplers. Press the couplers completely together with
a pair of pliers.
S TA R T I N G A N D S TO PPI N G
STARTING
1. Open the cover by pressing the STOP button.
2. Set the main switch to position 1. When you do this for the first time, a start up sequence starts where you select a four digit
PIN code among other things.
3. Press the START button and close the cover.
STOPPING
Press the STOP button.
A D J U S T I N G T H E RO B OT I C L AW N M O W E R TO S U I T T H E S I Z E O F YO U R L AW N
The mowing results depend on mowing time. Adjust the mowing time to suit your garden using the Timer function. You decide
what times during the day the robotic lawnmower is to work. The robotic lawnmower cuts approximately 90 m² / 0.022 acre per
hour and day for Automower® 420, 135 m² / 0.033 acre for Automower® 430X, 167 m² / 0.041 acre for Automower® 440 and
210 m² / 0.052 acre for Automower® 450X. For example, if your garden comprises 1200 m² / 0.3 acre of grass, the mower
should work 13 hours a day for Automower® 420, 9 hours a day for Automower® 430X, 7 hours a day for Automower® 440 and
6 hours a day for Automower® 450X.
M A I N T E N A N C E
1. The main switch should be in the 0 position during all work on the robotic lawnmower's chassis, such as cleaning or
replacing the blades. Replace the blades regularly for the best mowing result.
2. Never use a high-pressure washer or even running water to clean the robotic lawnmower. Never use solvents for cleaning.
3. All connections to the charging station (power supply, boundary and guide wire) must be disconnected if there is a risk of a
thunderstorm.
4. Fully charge the battery at the end of the season before winter storage.
P2_QG_1140535_420,430X,440,450X_2019_.indd 3
E N
2018-10-17 9:45:11