Preparation For Operation - GRAPHITE 58G210 Instrucciones De Uso

CONSTRUCTION AND USE
Drill is a battery powered tool. Drive consists of a DC commutator
motor with permanent magnets and planetary gear. Drill is designed
for screwing in and out screws and bolts in wood, metal, plastics and
ceramics, and for drilling holes in those materials. Cordless, battery-
powered power tools are especially useful for works in interior
furnishing, adaptation of premises etc.
Use the power tool according to the manufacturer's instructions
only.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
Quick-release chuck
1.
Ring of the quick release chuck
2.
Torque adjustment ring
3.
Gear switch
4.
Direction selector switch
5.
Battery lock button
6.
Battery
7.
Switch
8.
Battery level indicator (LED)
9.
Lighting
10.
LED diodes
11.
Charging station
12.
Charger
13.
* Differences may appear between the product and drawing.
MEANING OF SYMBOLS
NOTE
WARNING
ASSEMBLY / SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
Battery - 2 pcs
1.
Charger - 1 pce
2.
Charging station - 1 pce
3.
Driver bit - 1 pce
4.
Soft bag - 1 pce
5.

PREPARATION FOR OPERATION

REMOVING AND INSERTING THE BATTERY
• Set the direction selector switch (5) in middle position.
• Push battery lock buttons (6) and slide out the battery (7) (fig. A).
• Insert charged battery (7) into the handle holder, you should hear
when the battery lock buttons (6) snap.
BATTERY CHARGING
Drill is supplied with partially charged battery. The battery should
be charged in ambient temperature between 4
battery, or one that has not been used for a long time, will reach full
efficiency after approximately 3 to 5 charge/discharge cycles.
• Remove the battery (7) from the drill (fig. A).
• Connect the charging station (12) to the charger (13).
• Connect the charger (13) to mains socket (230 V AC).
• Put the battery (7) inside the charging station (12) (fig. B).
Once the battery has been placed in the charging station, LED
diodes (11) will light up on the charging station (12), different
configurations are possible (see below).
• Green diode on – indicates voltage on the connector.
• Green and red diodes on simultaneously – (when the battery
is placed in the charging station) indicate that the charging is in
progress.
• Red diode turns off, green diode stays on – indicate the battery
is fully charged.
Batteries heat up very strongly during charging process. Do not
work just after charging has been finished, wait until the battery
cools down to room temperature. It will prevent battery damage.
BATTERY LEVEL INDICATION
Each pressing the switch button turns on battery level indication.
Drill features battery level indication (4 LED diodes) (9). To check
battery level status, press the switch button (8) (fig. C). When all
diodes are lit, the battery level is high. When 2 diodes are on, the
battery is partially discharged. When only one diode is lit, the battery
is discharged and must be recharged.
SPINDLE BRAKE
Drill is equipped with electronic brake that stops the spindle
immediately after the switch button (8) is released. The brake
ensures precision when screwing or drilling and prevents free
spindle rotation after switching off.
SWITCHING ON / SWITCHING OFF
Switching on – press the switch button (8).
Switching off – release the switch button (8).
Each time the switch button (8) is pressed, the LED diode (10) lights
up to illuminate the workplace.
ROTATIONAL SPEED CONTROL
Increase or reduce pressure on the switch button (8) to adjust
drilling or driving speed while operating. Speed adjustment allows
for a soft start, which prevents dill slipping when drilling holes in
gypsum or glaze, and allows for operation control when screwing
in and out.
OVERLOAD CLUTCH
Set the torque adjustment ring (3) in appropriate position to
permanently set overload clutch to defined torque value. When the
set torque is reached, overload clutch disconnects automatically. It
prevents screwing screws too deep or damaging the drill.
TORQUE ADJUSTMENT
• Different screws and materials require different torque to be
applied.
• The bigger the number corresponding to given position, the
bigger is the torque (fig. D).
• Set the torque adjustment ring (3) to appropriate torque value.
• Always start operation with low torque.
• Increase the torque gradually until obtaining desired results.
• Use higher settings to unscrew screws.
• When drilling, choose setting marked with the drill symbol. The
torque is the greatest with this setting.
• Knowledge how to choose appropriate torque setting comes with
practice.
Setting the torque adjustment ring in the drilling position
deactivates the overload clutch.
0 C and 40 0 C. New
WORKING TOOL INSTALLATION
• Set the direction selector switch (5) in the middle position.
• By turning the ring of the quick release chuck (2) counter
clockwise (see mark on the ring) you can spread jaws enough to
insert drill or driver bit (fig. E).
• To install working tool, turn the ring of the quick release chuck (2)
clockwise and tighten.
12
OPERATION / SETTINGS