Publicidad
COMPONENTS {
}
1
❶ ❷
❸
A
B
C
FITTING {
}
2
K
J
M
L
APPLICATION {
}
3
T
SIZING
L/XL
G
D
E
F
H
S/M
P
N
O
U
I
X
11 in
28 cm
Y
8.25 in
21 cm
Patient Circumference
1
58 - 60 in
147 - 152 cm
2
55 - 58 in
140 - 147 cm
3
52 - 55 in
132 - 140 cm
4
49 - 52 in
125 - 132 cm
X
9.5 in
24 cm
Y
7.25 in
18 cm
Patient Circumference
1
44 - 49 in
111 - 125 cm
2
38 - 44 in
96 -111 cm
3
32 - 38 in
81 - 96 cm
28 - 32 in
71 - 81 cm
4
5
25 - 28 in
63 - 71 cm
R
Q
S
V
W
ENGLISH
BEFORE USING THIS DEVICE, PLEASE READ THE ENTIRE INSTRUCTION MANUAL. CORRECT APPLICATION AND CARE IS VITAL TO THE PROPER FUNCTIONING
OF THIS DEVICE.
I N D I C A T I O N S
Acute and chronic low back pain; post-operative support; activity related low back pain; disc herniation; stable, non-dis-
placed fractures.
C O N T R A I N D I C A T I O N S
Pregnancy and circulation; pulmonary; cardiovascular or skeletal conditions which have risk to be made worse as a result of
compression and/or pressure; unstable, displaced fractures.
W A R N I N G S A N D P R E C A U T I O N S
If you experience any pain, swelling, sensation changes, excessive discoloration, irritation to the skin or any unusual reaction
while using this product, consult your medical professional. If any distortion of the support panels, fraying or deterioration of
lace cables is noticed, discontinue use.
Do NOT expose to heat over 130°F (55°C)
C O M P O N E N T S { 1 }
A. BELT WINGS (ONE EACH SIDE)
D. POSTERIOR (REAR) PANEL SECTION
1.
Donning Mitt Section
E.
BOA® CLOSURE SYSTEM
2. Anterior (Front) Panel Section
F.
RIGID ANTERIOR (FRONT) PANEL
B. LATERAL EXTENSION (SIDE) PANELS
C.
T9 POSTERIOR (TALL REAR) PANEL
3.
Glide Track
L.
LORDOTIC INSERTS (OPTIONAL ACCESSORY - NOT INCLUDED) (Refer to Fitting {2}, Figure M)
B O A® C L O S U R E I N S T R U C T I O N S
TO LOOSEN BRACE
f Lift Boa® Knob up to release Boa® Lace (Figure G) and pull Rear Panel Section in opposite directions. (Figure T)
TO TIGHTEN BRACE
f Push Boa® Knob down and turn Boa® Knob clockwise to tighten the brace (Figure H)
f NOTE: The left Boa® Knob controls the top half of the brace. The right Boa® Knob controls the bottom half.
S I Z I N G { F I G U R E I }
f Begin by taking a circumferential measurement of the patient at the waist and the iliac crest. Use the larger measurement when
selecting your brace size.
f NOTE: It is not uncommon for the patient to experience post-surgical swelling, followed by weight loss (10-20+ lbs/4.5-9.1 kg).
The brace is designed with two (2) detachable Belt Wings which can be easily repositioned to achieve optimal fit.
f Match the patient's size to the Patient Sizing Chart (Figure I) .
F I T T I N G { 2 }
f Secure the Belt Wings to the Posterior (Rear) Section at the desired length (Figure I) . An approximation of fit can be achieved by
matching the tip of the hook attachment on the Posterior (Rear) Section to the desired sizing indicator on the Belt Wings (Figure J) .
B E LT W I N G T R I M M I N G I N S T R U C T I O N S ( O P T I O N A L )
f Once proper fit is confirmed, the excess material on the Belt Wings (that secures the Belt Wings to the Posterior (Back) Section) may
be trimmed. (Figure K)
f NOTE: Add-on components may require factoring more Belt Wing length. Do NOT trim excess material on the Belt Wings until
proper fit has been confirmed.
INSERTING/REMOVING LORDOTIC INSERTS (OPTIONAL ACCESSORY)
f NOTE: The Lordotic Inserts should be used and inserted when stepping down from the 631/637 configuration (Models 200631,
200637) to a 626/627 configuration (Models 200626, 200627).
REMOVING LORDOTIC INSERTS
f To remove, open the hook and loop pocket on the patient facing side of the Posterior (Rear) Section.
f Remove the Lordotic Inserts from the hook and loop pocket. (Figure M)
INSERTING LORDOTIC INSERTS
f To insert, open the hook and loop pocket on the patient facing side of the Posterior (Rear) Section.
f Slide the Lordotic Inserts inside the hook and loop pocket, making sure the arrow shaped hole point toward the midline of the
Posterior (Back) Section and the orange side is facing the patient. (Figure M)
S E C U R I N G / R E M OV I N G A N T E R I O R ( F R O N T ) PA N E L ( I N C L U D E D W I T H M O D E L S 20 0 631, 20 0 637, 20 0 627)
f Hold the Anterior (Front) Panel on the patient at the desired location. (Figure N) .
f Wrap the Anterior (Front) Panel Belt Wing over the Anterior (Front) Panel, making sure the loop strip (inward facing) on the Belt
Wing attaches to the hook strip (outward facing) on the Anterior (Front) Panel (Figure O & Figure P) .
f REMINDER: The Exos™ logo on the Anterior (Front) Panel should be facing upright and away from the patient.
S E C U R I N G / R E M O V I N G T 9 P O S T E R I O R ( TA L L R E A R ) PA N E L
f Lay the T9 Posterior (Tall Rear) Panel so the Glide Track is facing up.
f REMINDER: The Exos™ logo on the T9 Posterior (Tall Rear) Panel should be facing upright and away from the patient.
f Lay the Posterior (Back) Section over the top of the T9 Posterior (Tall Rear) Panel and insert the Glide Track Buttons through the
button holes located on either side of the Posterior (Back) Section (Figure Q).
f NOTE: Once the brace is donned, the narrow ends of the glide track should be positioned in the middle of the waist groove (just
superior to the illiac crest). Positioning of the T9 Posterior (Tall Rear) Panel may be adjusted superiorly by disengaging the hook
and loop attachment that connects the Glide Track with the T9 Posterior (Tall Rear) Panel, repositioning the T9 Posterior (Tall Rear)
Panel, then re-securing the Glide Track in the desired position (Figure R) .
S E C U R I N G / R E M O V I N G L AT E R A L E X T E N S I O N PA N E L S ( I N C L U D E D W I T H M O D E L 2 0 0 631, 2 0 0 637)
f Wrap the elastic band on the Lateral Extension (Side) Panels around the Belt Wings. Then slide each Lateral Extension (Side) Panel
toward the Posterior (Back) Section (Figure S) .
f REMINDER: The Lateral Extension (Side) Panels should be positioned on the inside of the Belt Wings.
f Secure the hook of the Lateral Extension (Side) Panels to the lateral sides of the T9 Posterior (Tall Rear) Panel facing away from the
patient (Figure P) .
f REMINDER: The Exos™ logo on the T9 Posterior (Tall Rear) Panel should be facing upright and away from the patient.
A P P L I C A T I O N I N S T R U C T I O N S { 3 }
BRACE APPLICATION
f Loosen brace.
f Prior to each application of the brace make sure the brace is fully extended by lifting the Boa® Knobs and pulling the Posterior
(Rear) Section apart (Figure T).
f Apply the brace to the patient by centering the Posterior (Rear) Section (Figure U) around the patient (on the back), then wrapping
the Belt Wings around the waist (toward the front) (Figure V). Secure the hook and loop attachment on the front.
f NOTE: When reapplying the brace, it is easiest for the patient to guide the belt by inserting a hand in the donning mit pocket.
(Figure V)
f NOTE: The Belt Wings may be secured to the Posterior (Rear) Section at an angle to accommodate a size differential between the
waist and hips (Figure W).
f Before tightening the brace make sure the Posterior (Rear) Section is positioned evenly on both sides of the patient. In order to achieve
optimal comfort and fit, it may be necessary to readjust and reposition the two (2) Belt Wings to the Posterior (Rear) Section.
f Push Boa® Knob down and turn Boa® Knob clockwise to tighten the brace (Figure H) . to the desired level of compression.
U S E A N D C A R E : ( C L E A N I N G & S T O R A G E I N S T R U C T I O N S )
Hand wash in cold water, less than 86°F (30°C), using mild soap. Air dry.
NOTE: If not rinsed thoroughly, residual soap may cause irritation and deteriorate material.
130˚F (55˚C)
Do NOT expose to heat
Do NOT iron.
Do NOT tumble dry.
Do NOT bleach.
over 130°F (55°C).
M AT E R I A L C O N T E N T S
Polyester, Nylon, Polyethylene, Terpolymer, Polycarbonate, Elastic, Steel, Zinc, Antimicrobial
F O R F I T T I N G T I P S O N T H I S E X O S ™ D E V I C E :
Visit the Exos™ Provider Center at: http://exosmedical.com/provider/formLSO or Scan the QR image with your smart-
phone
WA R R A N T Y:
DJO, LLC will repair or replace all or part of the unit and its accessories for material or workmanship defects for a period of
six months from the date of sale.
INTENDED FOR USE ON A SINGLE PATIENT.
Publicidad
