Preparation For Operation - VERTO 50G934 Instrucciones De Uso

5. Column
6. Drilling depth gauge bolt
7. Spindle return spring
8. Switch
9. Belt transmission casing
10. V belt tension locking bolt
11. Motor
12. Shaft to lower/lift the spindle
13. Handle
14. Knob
15. Bolt with locking wheel of the column clamping ring
16. Drill chuck guard
17. Drill chuck
18. Bolt for spindle sleeve slack adjustment
* Differences may appear between the product and drawing.
MEANING OF SYMBOLS
CAUTION
WARNING
ASSEMBLY/SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
1. Drill chuck guard
2. Drill chuck + key
3. Head
4. Base
5. Column clamping ring
6. Bolt with wheel
7. Work table
8. Bolt for work table fixing
9. Column
10. Column locking bolts
11. Handle
12. Knob
13. Hexagonal key
14. Drilling depth gauge bolt
15. Nut for limiter bolt
16. Indicator

PREPARATION FOR OPERATION

Bench drill is supplied disassembled. Take parts of the bench drill out
of the package and assemble in the below described order.
BASE, COLUMN AND WORK TABLE ASSEMBLY
• Place the column (5) onto the base (1) and fix with the supplied bolts.
• Place base (1) and column (5) on flat and even surface.
• Slide column clamping ring (4) (with the work table 3) onto column
(5) (fig. A).
• Position work table (3) opposite to the base (1).
• Attach and tighten bolt with locking wheel of the column clamping
ring (15).
INSTALLATION OF HEAD AND EQUIPMENT
• Use hexagonal key to loosen screws in the bench drill head body,
which lock the head on the column (5).
• Place head (with spindle pointed towards the work table) onto
column (5) and tighten previously loosened screws.
• Attach knobs (14) on the handles (13).
• Screw handles (13) into holes in the shaft for the spindle lowering
/ lifting (12).
• Install drill chuck guard (16).
• Place and tighten drill chuck guard (16) on the spindle sleeve (with
• Assemble drilling depth gauge bolt (6) with nuts (b) and indicator
• Clean grease off the spindle Morse taper and taper of the drill chuck
• Lift the drill chuck guard (16) and slide drill chuck (17) onto spindle
• Bring down the drill chuck guard (16).
To firmly assemble drill chuck in the spindle sleeve, it is
recommended to press them against each other. To do that, put
wooden piece on the work table and turn handle to move down
the spindle sleeve until drill chuck contacts the wooden piece.
Apply moderate pressure.
V BELT TENSION ADJUSTMENT AND CHECK
You can open belt transmission casing only when the bench drill is
disconnected from the power supply. After every change of V belt
setting, close the belt transmission casing and secure it with a screw.
• Unscrew fixing screw and lift belt transmission casing (9).
• Ensure the V belt position on belt pulleys is correct.
• Check tension of the V belt (a V belt tension is correct when it moves
- 1 set
- 1 pce
- 1 pce
• If the V belt is too loose, loosen V belt tension locking bolt (10) and
- 1 pce
- 1 pce
• Set appropriate tension of the V belt and tighten V belt tension
- 1 pce
- 1 pce
• Close belt transmission casing (9) and secure it with the screw.
- 1 pce
DRILL INSTALLATION ON A WORKSHOP BENCH
- 1 pce
- 3 pcs
- 3 pcs
- 3 pcs The drill should be firmly fixed to a workbench with the use of four
- 2 pcs
fixing holes (2) designed for such purpose and located in the drill base
- 1 pce (1) (fixing bolts not included). It will assure safe operation of the tool.
- 2 pcs Fixing holes (2) allow to use screws or bolts 12 mm in diameter.
- 1 pce
SWITCHING ON / SWITCHING OFF
Before connecting the bench drill to a power supply, always check
that power supply voltage matches rated voltage shown on the
rating plate fixed to the bench drill.
Microswitch located in the belt transmission cuts off power
supply for the drill motor, whenever the casing is opened. When
the belt transmission casing is opened it is impossible to switch
on the bench drill.
Microswitch is an additional protection of the user against
potential body injury caused by moving parts of the belt
transmission of the drill.
Switching on
• Open lid (d) of the switch (8) (fig. D).
• Press the switch button (I).
Switching off
• Press the switch button (O).
11
shielding part of the guard towards operator).
(c) in the hole of drill chuck guard (16) so it is free to move through
the hole in the head casing (fig. B).
(17).
Morse taper.
by approximately 10 mm after pressing it in the middle of the
distance between its pulleys) (fig. C).
allow the spring to pull the motor (11) backwards.
locking bolt (10).
OPERATION / SETTINGS