Description Of Safety Symbols; Assembly Instructions; Precautions During Operation - Guarany 0426.00 Manual Del Operador

OPERATOR'S MANUAL |Big Sucker (Siphon & Discharge Pump)
Always follow the maintenance instructions described by the manufacturer regarding
the replacement of components, use only Guarany original parts. Failure to follow
these procedures, will invalidate the warranty.
Training of technicians and operators: For the correct and safe use of this
equipment please consult our conditions using the telephone numbers in this manual.

4.1 DESCRIPTION OF SAFETY SYMBOLS

Attention / Warning / Caution
Read the manual
Use protective clothing to prevent risks from chemicals
Wear fully water proof protective gloves
Use fully water proof protective boots
Use facial protection - face visoror goggles
Use respiratory protection

5. ASSEMBLY INSTRUCTIONS

When opening the carton, locate and identify all the components listed in Figure 2.
Adaptor
Pump assembly
(Code 11017)
(Code 10733)
F
Tank with hose
wire reinforced nylon
and flow contol
tubing, length: 1000mm
(Code 11027)
E
G
Siphon tube
Operating
(Code 11016) Steel tubing,
Manual
length: 1600mm
(Code 11023)
Operating manual
Figure 2. Equipment components
31
5.1 REVERSIBLE PRESSURE PUMP - Figure 3
Attach the pump unit (B) with a simple turn of the threaded connector into the
neck of the tank (A).
Figure 3
5.2 DISCHARGE VALVE AND SUCTION AND
DISCHARGE TUBES - Figure 4
Attach the aluminium siphon tube (E) to the flow control valve (H) using the threaded
collar; then fit the adaptor (C) (the grooved side) into the aluminum tube.
Finally, select the siphon hose (F or G) most appropriate for the intended operation and
fit it into adaptor (C).
F ou G
C
E H
Figure 4 Assembly sequence of the complete flow control unit
6. OPERATION OF EQUIPMENT
IMPORTANT
The Guarany Siphon & Discharge pump was designed for liquid
lubricants, water and other non-corrosive fluids
OPERATOR'S MANUAL |Big Sucker (Siphon & Discharge Pump)
WARNING - NOT RECOMMENDED –Applications which
may cause damage are not covered by the warranty:
LIQUIDS WHOSE TEMPERATURE IS ABOVE 70°C (158°F)
WITH FUELS OR STRONG CHEMICALS INCLUDING ACIDS AND
ALKALIS
* Note: In the event such fluids are used in the equipment, the equipment must be immediately drained
and cleaned.
!
ATTENTION
WHEN USING THIS EQUIPMENT WITH SUBSTANCES THAT MAY BE HARMFUL
TO HEALTH. WE RECOMMEND THE USE OF PROTECTION FOR THE BODY,
HANDS, FEET, EYES AND RESPIRATORY SYSTEM.
PERSONAL PROTECTIVE EQUIPMENT (PPE) MAY VARY DEPENDING ON THE
CHEMICAL. CONSULT THE MANUFACTURER OF THE PRODUCT TO BE USED,
TO CHECK IF THERE ARE SPECIFIC REQUIREMENTS REGARDING THE
RECOMMENDED PPE.

6.1 PRECAUTIONS DURING OPERATION

!
ATTENTION
Do not smoke, eat or drink while filling the tank with chemicals and/or during
operation (suction or discharge).
a) When working with toxic liquids, keep children, pets and onlookers away from
the work area.
b) Never fill the tank beyond its maximum capacity (6 litres), which is clearly
indicated; in the event of chemical spillage on the tank or on the ground, wipe it up
immediately, avoiding any contamination.
c) Check for the presence of any leaks. If any are found, do not use the equipment
until the problem is solved.
d) Only use the unit in an upright position ("standing up");
e) TEST that the equipment is switched to the suction function before submerging
the tube in the liquid to begin siphoning. This precaution is necessary because if
!
the pressurised tank is without any liquid in the discharge function, actuating the
pump and squeezing the trigger control, will cause air to be expelled into the
target liquid which may cause splashing that could result in possible accidents, for
example, contamination and /or burns.
f) Do not transport, leave or store the equipment while still pressurized.
g) Empty the tank after use and when using authorized flammable liquids, keep
the tank nozzle without the pump/cylinder.
h) Never carry the equipment by holding the pump handle without first locking it
into the tank, as this can damage the pump. Before depressurizing the tank and for
any transport operation, lock in the handle of the pump, according to Figure 5.
Do not transport!
With handle
unlocked.
Figure 5 Correct use of the handle for depressurizing the tank and transportation
6.2 SUCTION
To activate the SIPHON function, first make sure that the pump (B) is well
threaded into the tank and that the safety pressure relief valve is in the closed
position (Figure 6 A, ensuring the sealing of the pressure chamber).
VALVE CLOSED
VALVE OPEN
Figure 6
Possible positions of the safety pressure relief valve
32