Publicidad
Idiomas disponibles
Idiomas disponibles
Stove start up
Remove
any
might burn from the firebox and from
the glass (various instructions and
adhesive labels).
Charge pellet
Fuel is loaded from the upper part of the thermostove
by opening a door. Pour the pellets in the hopper.
When empty contains about 10 kg of pellets.
This is easier if performed in two steps:
• Pour half of the contents of the bag into the hopper
and wait for the fuel to settle on the bottom.
• Then pour in the rest.
Never remove the protection grille
in the hopper. When filling, do not
let the sack of pellets touch any hot
surfaces.
The brazier should be cleaned
before each starting.
First lighting of the stove
• Before switching on, make sure that the grate
is clean and empty of any pellet residues from
previous combustions. Otherwise make sure you
empty and clean it
• Fill the container 3/4 full with the pellets
recommended by the manufacturer
• Connect the stove to an electrical outlet with the
cable that has been supplied
• Press the lighting switch located on the back part
of the stove
• The upper display will read " " O FF
• Press the button
moments the smoke extractor and the lighting
resistor will start and the display will read " " S TART
The led resistance is switched on
• After 1 minute the display will read " " L OAD
P E L L E T" " , the stove will load the pellets and
P E L L E T
continue lighting the resistor
• Once the appropriate temperature has been
reached the display will read " " FLAM E LIGHT
this means that the stove has begun the last
phase in lighting, at the end of which the stove
will be completely operational; The led resistence
is switched off
• After some minutes the display will show the
words " " W O RK
W O RK" " alternating room temperature
and current working power. The stove is now
completely on
• When the stove reaches the set temperature,
the display will show " " MOD U LATION
16
components
which
O FF" "
for 2 seconds. After a few
S TART" " ;
FLAM E LIGHT" " :
MOD U LATION" " .
Before lighting a small amount
of smoke may fill the combustion
chamber.
We highly recommend to turn
to our Authorized Service Centre
for the installation and the first
ignition of the device as it not only
carries out the installation perfectly but
also verifies the regular operation of it.
During the first lighting the environment
should be well ventilated since during the
first hours of operation unpleasant odours
could develop due to the physical stabilizing
of the paint and from the grease in the tube
bundle.
Stove switching off
To switch off the stove, press the key
control board until you read " " C LE AN IN G FI N AL
on the display. After the stove has been switched
off, the fan continues working for a set time in
order to grant a fast smokes exhaust from the
combustion chamber.
If you have a model with remote control, you just
need to switch the remote control off keeping
the key pressed for 2 seconds and confirming the
selection pressing the key SEND.
If you try to switch on the stove during this phase,
the display will show " " w ait in g c o ol in g
means wait for cooling) in order to inform you
a switching off phase is running. Wait until the
cooling phase is completely off and the display
shows " " O FF
O FF " " before staring a new light up.
REMARKS:
• Do not continuously turn the stove on and off as
this could provoke sparks that could shorten the
life of the electrical components.
L OAD
• Do not touch the stove with wet hands: the stove
has electrical components that could produce
sparks if handled incorrectly. Only authorized
technicians can resolve possible problems.
• Do not remove any screws from the fire chamber
without first lubricating them well.
• Never open the glass door of the pellet stove
while the stove is in operation.
• Be sure that the brazier basket is positioned
correctly.
• The flue system must be suitable for inspecion. If
it cannot be removed, it must have some holes for
inspection and cleaning.
on the
C LE AN IN G FI N AL" "
w ait in g c o ol in g " " (that
Publicidad
