Mhouse Kit RMEN Instrucciones Y Advertencias Para La Instalación Y El Uso página 7

RMEN can memorise up to 12 transmitters. To memorise other transmitters, a first transmitter must already be memorised on RMEN, memorised with the pro-
cedure described in paragraph 9.5 (to verify this condition, read paragraph 9.3).
Lastly, decide which procedure to follow to memorise other transmitters according to specific requirements.
Caution! - To perform the following procedures, a second previously memorised transmitter must be available.
9.6 - "MODE I" procedure (to memorise other transmitters, using a previously memorised version)
The procedure memorises the new transmitter in "Mode I", regardless of the mode in which the old transmitter was memorised (therefore it is not important to
know how the hold transmitter was memorised).
8
new
s
old
01. Press and hold ■ of the NEW transmitter, for at least 8 seconds. Then release the key (Note - In this case the motor does not perform any movement).
02. Press any key of an OLD transmitter (memorised!) 3 times.
03. Press the key ■ of the NEW transmitter once.
04. The motor then completes 3 LONG motions (= memorisation complete). Note - If the motor performs 6 LONG motions means that the memory is full.
9.7 - "MODE II" procedure (to memorise other transmitters, using a previously memorised version)
The procedure memorises the new transmitter in "Mode II", regardless of the mode in which the old transmitter was memorised (therefore it is not important to
know how the hold transmitter was memorised).
8
new
s
old
01. Select the key to be memorised on the NEW transmitter (for example: ▼) and press and hold for at least 8 seconds. Then release the key (Note - In this
case the motor does not perform any movement).
02. (Within the next 5 seconds) On the OLD transmitter press and hold any key (memorised) for approx. 5 seconds until the motor has completed 2 SHO RT
motions and then release.
03. (Within the next 5 seconds) Press the same key as before, on the OLD transmitter, for as many times as the number of the command you wish to mem-
orise:
press once = Step - Step command
press 3 times = Down - Stop command
After approx. 3 seconds, the motor performs a number of motions corresponding to the selected command.
04. (Within the next 2 seconds) On the NEW transmitter, press and hold the same key pressed above, and release as soon as the motor has completed the first
of the 3 LONG motions (= memorisation complete). Note - If the motor performs 6 LONG motions means that the memory is full.
Note - In point 03 if the motor does not perform the same number of motions as the number of the selected command, cancel the procedure by waiting for a
few seconds without pressing any other key. Then repeat the procedure from the start.
9.8 - Memorising a NEW transmitter, duplicating the commands of an OLD transmitter
This enables memorisation of a NEW transmitter, duplicating the commands of an OLD transmitter.
In this case it is essential to know in which Mode (I or II) the old transmitter was memorised.
new 3
s
old
01. On the NEW transmitter, select any key (if memorised in Mode I) or the required key (if memorised in Mode II) and press and hold for at least 3 seconds. Then
release the key.
02. On the OLD transmitter, select any key (if memorised in Mode I) or the required key for transfer of the function (if memorised in Mode II) and press and hold
for at least 3 seconds. Then release the key.
03. On the NEW transmitter, press the same key pres sed before in point 01 for at least 3 seconds and then release.
04. On the OLD transmitter, press the same key pres sed before in point 02 for at least 3 seconds and then release.
05. The motor then completes 3 LONG motions (= memorisation complete). Note - If the motor performs 6 LONG motions it means that the memory is full.
Memorising the OTHER TRANSMITTERS
3 new
x
3
1/
old x
2
press twice = Up - Stop command
press 4 times = Stop command
3 3
s s
new
/ 4
... x new
(1/... /4)
3
s
old
3
3
English – 6