Normal Operation; Qs Link Input(S) Setup - Lutron Energi Savr Node QS Manual De Instrucciones

Energi Savr Node

Normal Operation

In normal operation, the following buttons allow the user to ac-
cess certain basic functions:
1. Zone buttons – Press to select a zone.
2. (Raise) — QSNE-4T10-D: Raises zone light level in 1%
increments from 0-100%.
— QSNE-4S10-D: Turns selected zone on.
3. (Lower) — QSNE-4T10-D: Decreases zone light level in 1%
decrements from 100-0%.
— QSNE-4S10-D: Turns selected zone off.
Note: On QSNE-4T10-D only - For any zone, simultaneously
pressing and holding the
zone between high end and low end.

QS Link Input(s) Setup

seeTouch QS Wallstation or GRAFIK Eye
®
and Scenes + Off
Assigns a seeTouch QS Wallstation or GRAFIK Eye
®
any ESN QS unit zone on the QS link.
1. To assign a seeTouch QS Wallstation or GRAFIK Eye
®
to an ESN QS unit(s), simultaneously press and hold the top and
bottom buttons on the wallstation or GRAFIK Eye
3 seconds. The QS link enters Programming Mode. The input
Group A and Group B LEDs and the 'H', 'M', and 'L' LEDs on the
ESN QS unit(s) will flash sequentially in groups.
2. To assign or un-assign desired zone(s) to a wallstation, press
and hold the Zone button for the desired zone until the LED
changes state. A blinking 'Zone' LED indicates an assigned
zone.
3. To save settings, simultaneously press and hold the top and
bottom buttons on the wallstation or GRAFIK Eye
seconds.
Note: For more advanced programming information, refer to the
online Programming Guide at:
http://www.lutron.com/InstallationInstructions/230Vesn
Energi Savr Node QS for 0-10 V / Switching Installation Guide
TM
QS for 0-10 V / Switching
TM
and buttons will toggle the
QS unit - Scenes
®
QS unit to
®
QS unit
®
QS unit for
®
QS unit for 3
®
|
Installation Guide
Using LEDs to troubleshoot
WARNING! Danger of Shock. May result in serious
injury or death. DO NOT WIRE WHEN LIVE! Switch off
power to all power feeds via circuit breaker or isolator
before wiring or servicing the ESN QS unit.
Buttons and LEDs in the unit are used for programming
and troubleshooting. If wiring is exposed when accessing
buttons and LEDs, the unit must be accessed by a certified
electrician, following local codes.
Normal Mode LED Behavior
LED LED Behavior
Continuous On
Power
Off
Continuous On
Occ
(Occupancy 1 flash per second
Sensor)
Off
Continuous On
Photo
Flashing
(Daylight
Sensor )
Off
Continuous On
IR
(Infrared Re- Flashing
ceiver)
Off
On/Flashing
QS
3 quick flashes
(QS Link) every 4 seconds
Off
Continuous On
Input
1 flash per second
CCI Continuous On
(Contact
Closure Input)
Rapid flash
1 flash per second
Program
Off
Description
Normal operation
General system failure/
No power
Sensor detects Vacancy
Sensor detects Occupancy
Sensor never detected
Sensor is detected
Sensor information
transmitting on the QS link
Sensor never detected/
sensor not seeing light
Receiver is detected
IR button press detected
Receiver never detected
Device transmitting/
receiving on the QS link
Communication error
Device not transmitting/
receiving on the QS link
Wired input
Remote input
Normal operation/Contact
Closed/Jumpered
Emergency Mode/Contact
Open/Jumper missing
Device is in Program Mode
Device is in Normal Mode
Lutron 11
|
®