GRAPHITE 59G812 Instrucciones De Uso página 16

• Clean guides and apply thin layer of solid grease.
• All handles and knobs should be kept clean.
• Clean the laser projector lens with a brush.
REPLACING THE CUTTING DISC
• Press the cutting disc guard lever (5).
• Raise the cutting disc guard (7) and loosen the central plate
mounting bolt (40) (fig. H).
• Move the central plate (41) to the left to provide access to
the cutting disc mounting bolt.
• Press the spindle lock button (6) and rotate the cutting disc
until it locks.
• Using the special spanner (included), loosen and unscrew
the cutting disc mounting bolt.
• Remove the external washer and remove the cutting disc
(paying attention to the reducer ring, if provided).
• Remove all impurities from the spindle and cutting disc
mounting washers.
• Mount a new cutting disc by performing the described
activities in a reverse order.
• Once completed, make sure all spanner and adjusting tools
are removed and all bolts, knobs and screws are tightened
and secured.
The cutting disc locking bolt has left-hand thread.
Exercise utmost attention when gripping the cutting disc.
Use protective gloves to provide protection for your
hands against sharp teeth of the cutting disc.
REPLACING BATTERIES IN THE LASER UNIT
The laser unit is powered with two AAA batteries, 1.5 V.
• Open the battery compartment lid (36) (fig. F).
• Removed used batteries.
• Insert new batteries. Observe the polarity.
• Installed the battery compartment lid.
REPLACING THE CARBON BRUSHES
Worn (shorter than 5 mm), burnt or cracked motor carbon brushes
should be immediately replaced. Both carbon brushes should be
always replaced at the same time.
• Loosen the covers of the carbon brushes (8).
• Remove the worn carbon brushes.
• Remove any carbon dust using compressed air.
• Insert new carbon brushes (brushes should easily slide into
the brush holders).
• Fasten the covers of the carbon brushes (8).
After the carbon brushes are replaced, switch on the tool
with no load and wait for 1-2 minutes to make the carbon
brushes fit the motor commutator. Carbon brushes
should be replaced by a qualified person using original
spare parts only.
All types of faults and defects should be eliminated by an
authorised service of the manufacturer.
SPECIFICATIONS
RATED DATA
Mitre saw
Parameter
Power supply voltage
Power supply frequency
Rated power
NOISE AND VIBRATION DATA
Acoustic pressure level: Lp
Acoustic power level: Lw
Vibration acceleration value: a
* The right to make changes is reserved.
"Grupa Topex Spółka z ograniczoną odpowiedzialnością" Spółka
komandytowa with seat in Warsaw at ul. Pograniczna 2/4 (hereinafter
Grupa Topex) informs, that all copyrights to this instruction (hereinafter
Instruction), including, but not limited to, text, photographies, schemes,
drawings and layout of the instruction, belong to Grupa Topex exclusively
and are protected by laws accordingly to Copyright and Related Rights Act
of 4 February 2004 (ustawa o prawie autorskim i prawach pokrewnych, Dz.
U. 2006 No 90 item 631 with later ammendments). Copying, processing,
publishing, modifications for commercial purposes of the entire Instruction
or its parts without written permission of Grupa Topex are strictly forbidden
and may cause civil and legal liability.
Value
230V~
50Hz
1800W
15
No load spindle speed:
Angle sawing range
Mitre sawing range
Outside diameter of cutting disc
Hole diameter of cutting disc
Workpiece
dimensions
45° x 45°
angle/mitre
Guide length
Laser class
Laser power
Laser wavelength
Protection class
Weight
Year of manufacture
= 95,2 dB(A) K = 3 dB(A)
A
= 108,2 dB(A) K = 3 dB(A)
A
h
ENVIRONMENTAL PROTECTION
Electrically powered products should not be disposed of
with household wastes, but should be utilised in proper
recycling centres. Obtain information on waste recycling
from your seller or local authorities. Used electric and
electronic equipment contains substances active in the
natural environment. Unrecycled equipment constitutes
a potential risk for the environment and human health.
-1
4800min
± 45°
0° ÷ 45°
254mm
30mm
0° x 0° 90 x 280mm
45° x 0° 90 x 200mm
50 x 200mm
0° x 45° 50 x 280mm
195mm
2
< 1mW
λ = 650nm
II
16 kg
2020
= 2,936 m/s 2 K = 1,5 m/s 2