Technical Data - YATO YT-85401 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 65
PROPERTIES OF THE PRODUCT
The combustion pump permits to pump water wherever electrical power supply is not available. A correct, reliable and safe func-
tioning of the device depends on the proper operation, therefore:
Before any work with the device, it is required to read the whole manual and keep it.
The supplier will not be held responsible for any damage and injuries caused by operation of the tool for any purpose other than
intended or by inobservance of safety regulations and recommendations indicated in the present manual. Should the tool be used
for any purpose other than intended, the guarantee will become void and the user will loose any contractual rights.
EQUIPMENT
The pump is supplied complete, however it requires certain preparation, as described in the manual.

TECHNICAL DATA

Parameter
Catalogue number
Weight (without fuel)
Dimensions
Fuel tank capacity
Oil tank capacity
Water inlet/outlet diameter
Maximum capacity
Maximum lifting height
Maximum suction height
Maximum water temperature
Maximum diameter of foreign matter
The engine – type
Number of cylinders
Number of strokes
Cooling
Capacity
Power
Nominal rate of rotation
Fuel consumption at the nominal rate of rotation
Type of engine oil
Type of sparking plug
Emissions
Noise – acoustic pressure level L
pA
Noise – acoustic power level L
wA
GENERAL SAFETY CONDITIONS
WARNING! During operation of a pneumatic tool, it is recommended to always observe the basic safety regulations including
those mentioned below, in order to diminish the risk of fire, electric shock and injury.
Before operation of the tool can be commenced, the whole manual must be read and kept.
ATTENTION! Read all the instructions mentioned below. If they are not observed, there is a risk of electric shock, fire or injury.
The notion of „pneumatic tool" that is used in the instructions refers to all tools that are powered with a stream of compressed air
at appropriate pressure.
OBSERVE THE FOLLOWING INSTRUCTIONS
Place of work
The place of work must be well lit and kept clean. Disorder and weak light may be causes of accidents. Do not work indoors.
The exhaust gases and fuel vapours are toxic. Poisoning them can lead to accidents and cause serious injury. Prevent access of
children and unauthorized persons to the place of work. Loss of concentration may cause loss of control of the tool.
O R I G I N A L
GB
Unit of measurement
YT-85401
[kg]
[mm]
485 x 415 x 415
[l]
[l]
[mm / '']
[m
3
/h]
[m]
[m]
[ºC]
[mm]
CP168FB
[cm
3
]
[kW]
[min
]
-1
[g/h]
SAE 15W-40
F7RTC
[dB (A)]
82,1 ± 3,0
[dB (A)]
95,4 ± 3,0
I N S T R U C T I O N
Value
YT-85402
25
28
510 x 415 x 415
3,6
3,6
0,6
0,6
50 / 2
80 / 3
30
50
25
20
8
8
45
45
50
80
CP168FB
1
1
4
4
air
air
196
196
3,6
3,6
3600
3600
1900
1900
SAE 15W-40
F7RTC
81,9 ± 3,0
95,0 ± 3,0
YT-85403
30
570 x 530 x 515
3,6
0,6
100/4
78
20
8
45
100
CP170F
1
4
air
208
4,0
3600
1950
SAE 15W-40
F7RTC
81,9 ± 3,0
94,9 ± 3,0
13

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Yt-85402Yt-85403

Tabla de contenido