Atlas Copco EP12XS HR13 Instrucciones De Operación página 6

Safety and operating instructions
) Use high-quality inserted tools or consumables to
8
minimize exposure to excessive levels of vibra-
tions.
) Minimize exposure to reaction forces.
9
• When cutting:
A cut-off wheel can get stuck if the wheel is
either bent or if it is not guided properly. Make
sure to use correct flanges for cut-off wheels
and avoid bending the wheel during cut-off
operation.
• When drilling:
The drill might stall when the drill bit breaks
through. Makes sure you use support handles
if the stall torque is too high. The safety stand-
ard ISO11148 part 3 recommends to use
something to absorb the reaction torque above
10 Nm for pistol grip tools and 4 Nm for
straight tools.
• When using direct driven screw or nutrunners:
Reaction forces depend on tool setting and joint
characteristics. The ability to bear reaction
forces depends on the operator's strength and
posture. Adapt the torque setting to the operat-
or's strength and posture and use a torque arm
or reaction bar if the torque is too high.
) Use dust extraction system or mouth protection
1 0
mask in dusty environments.
Country of origin
Please refer to the information on the product label.
Spare parts
Parts without ordering number are not delivered
separately for technical reasons.
The use of other than genuine Atlas Copco replace-
ment parts may result in decreased tool performance
and increased maintenance and may, at the company
option, invalidate all warranties.
Warranty
Contact the Atlas Copco sales representative within
your area to claim a product. Warranty will only be
approved if the product has been installed, operated
and overhauled according to the Operating Instruc-
tions.
Please also see the delivery conditions applied by
the local Atlas Copco company.
ServAid
ServAid is a utility for providing updated product
information concerning:
- Safety instructions
- Installation, Operation and Service instructions
- Exploded views
6
EN
© Atlas Copco Industrial Technique AB - 9836 1295 03
ServAid facilitates the ordering process of spare
parts, service tools and accessories for the product
of your choice. It is continuously updated with in-
formation of new and redesigned products.
You can use ServAid to present content in a spe-
cific language, provided translations are available,
and to display information about obsolete products.
ServAid offers an advanced search functionality of
our entire product range.
ServAid is available on DVD and on the web:
http://servaidweb.atlascopco.com
For further information contact your Atlas Copco
sales representative or e-mail us at:
servaid.support@se.atlascopco.com
Technical data
Noise and vibration emission
Noise (in accordance with ISO15744)
Sound pressure level
Sound power level
Uncertainty
Vibration total value, valid from 2010
(3-axes value in accordance with ISO28927-2)
Vibration value
Uncertainty
Vibration value, valid until 2009
(1-axis value in accordance with ISO8662-7)
Vibration value
Noise and Vibration Declaration State-
ment
These declared values were obtained by laboratory
type testing in accordance with the stated standards
and are suitable for comparison with the declared
values of other tools tested in accordance with the
same standards. These declared values are not ad-
equate for use in risk assessments and values meas-
ured in individual work places may be higher. The
actual exposure values and risk of harm experienced
by an individual user are unique and depend upon
the way the user works, the workpiece and the
workstation design, as well upon the exposure time
and the physical condition of the user.
We, Atlas Copco Industrial Technique AB,
cannot be held liable for the consequences of using
the declared values, instead of values reflecting the
actual exposure, in an individual risk assessment in
a work place situation over which we have no con-
trol.
This tool may cause hand-arm vibration syndrome
if its use is not adequately managed. An EU guide
to managing hand-arm vibration can be found by
EP12XS HR13
dBA
85
96
3
2
m/s
6
1.1
2
m/s
2.5