Manufacturer's Warranty; Spare Parts Lists - REMS Hydro-Swing 22V Instrucciones De Servicio

eng
4.1. Servicing
WARNING WARNING
Before service work, pull the mains plug or remove the battery!
Clean the REMS Hydro-Swing 22 V regularly, especially if it has not been in
use for some time. Keep the bending contours of bending formers (11) and
back formers (8) clean. Use REMS CleanM (Art.-No. 140119) or mild soap and
a damp cloth for cleaning. Do not use household cleaners. These often contain
chemicals which can damage the plastic parts. Never use petrol, turpentine,
thinner or similar products for cleaning. Never immerse the REMS Hydro-Swing
22 V in liquid
5. Behaviour in the event of faults
5.1. Fault: Drive unit does not work.
Cause:
● Worn carbon brushes.
● Not enough hydraulic oil in the system..
● Battery depleted or defective.
● Drive unit defective.
● Overpressure valve responds.
● Pipe bender defective.
5.2. Fault: 90° bend cannot be fully made.
Cause:
● Not enough hydraulic oil in the system..
● Back former support (6) fi tted incorrectly.
● The strength of the pipe to be bent is too high.
● Battery depleted or defective.
● Drive unit defective.
5.3. Fault: No useful bend.
Cause:
● Pipe size does not correspond to the bending former (11) and/or the back
formers (8).
● Back former support (6) fi tted incorrectly.
● Pipe is unsuitable for bending.
6. Disposal
The drive unit, batteries, rapid chargers and power supply unit may not be
thrown in the domestic waste when no longer used. They must be disposed of
according to the legal regulations. Lithium batteries and battery packs of all
battery systems may only be disposed of in the discharged state, all contacts
of incompletely discharged lithium batteries and battery packs must be covered,
for example, with insulating tape.

7. Manufacturer's Warranty

The warranty period shall be 12 months from delivery of the new product to the
fi rst user. The date of delivery shall be documented by the submission of the
original purchase documents, which must include the date of purchase and the
designation of the product. All functional defects occurring within the warranty
period, which are clearly the consequence of defects in production or materials,
will be remedied free of charge. The remedy of defects shall not extend or
renew the warranty period for the product. Damage attributable to natural wear
and tear, incorrect treatment or misuse, failure to observe the operational
instructions, unsuitable operating materials, excessive demand, use for unau-
thorized purposes, interventions by the customer or a third party or other
reasons, for which REMS is not responsible, shall be excluded from the warranty.
Services under the warranty may only be provided by customer service stations
authorized for this purpose by REMS. Complaints will only be accepted if the
product is returned to a customer service station authorized by REMS without
prior interference and in a fully assembled condition. Replaced products and
parts shall become the property of REMS.
4.2. Inspection/Repair
ATTENTION ATTENTION
Before any repair work, pull the mains plug or remove the battery! This
work may only be performed by qualifi ed personnel.
The sealing rings (O-rings) in the electro-hydraulic drive units are subject to
wear. These must therefore be checked and renewed from time to time. In case
of poor bending force or loss of oil, the drive unit must be inspected and repaired
by a REMS authorised customer service station.
The gear runs in a life-long grease fi lling and therefore needs no lubrication.
The DC motor of the REMS Hydro-Swing 22 V has carbon brushes. These
cannot be replaced; the DC motor must be replaced.
NOTICE
Damaged or worn back former supports, back formers and bending formers
cannot be repaired.
Remedy:
● Have the DC motor changed by qualifi ed personnel or an authorised REMS
customer service workshop.
● Have the REMS Hydro-Swing 22 V checked/repaired by an authorised REMS
customer service workshop.
● Charge the battery with the rapid charger or change the battery.
● Have the drive unit checked/repaired by an authorised REMS customer service
workshop.
● Pipe is unsuitable for bending. Only use approved pipes.
● Have the pipe bender checked/repaired by an authorised REMS customer
service workshop.
Remedy:
● Have the REMS Hydro-Swing 22 V checked/repaired by an authorised REMS
customer service workshop.
● Fit back former supports as described in 2.2.
● Only use approved pipes.
● Charge the battery with the rapid charger or change the battery.
● Have the drive unit checked/repaired by an authorised REMS customer service
workshop.
Remedy:
● Use a bending former and/or back formers appropriate to the pipe size.
● Fit back former supports as described in 2.2.
● Only use approved pipes.
The user shall be responsible for the cost of shipping and returning the product.
A list of the REMS-authorized customer service stations is available on the
Internet under www.rems.de. For countries which are not listed, the product
must be sent to the SERVICE-CENTER, Neue Rommelshauser Strasse 4,
71332 Waiblingen, Deutschland. The legal rights of the user, in particular the
right to make claims against the seller in case of defects as well as claims due
to wilful violation of obligations and claims under the product liability law are
not restricted by this warranty.
This warranty is subject to German law with the exclusion of the confl ict of laws
rules of German International Private Law as well as with the exclusion of the
United Nations Convention on Contracts for the International Sales of Goods
(CISG). Warrantor of this world-wide valid manufacturer's warranty is REMS
GmbH & Co KG, Stuttgarter Str. 83, 71332 Waiblingen, Deutschland.

8. Spare parts lists

For spare parts lists, see www.rems.de → Downloads → Parts lists.
eng
11