Miche REVOX WR DX Manual De Uso Y Mantenimiento página 8

HUBS
2
Warning
!
If you have any doubt whatsoever your service-repair
ability, please take your bicycle to a qualified repair shop.
Before any maintenance operations on your wheels, always
wear gloves and protection glasses.
Use original spare parts exclusively provided by
Fac Michelin S.r.l.
When replacing any broken sealed bearings please ensure sea-
led bearing correct measure and specification are used.
Rear hub
Right side 26x17x5 (6803)
Left side 26x17x5 (6803)
The WR hubs are easy to maintain. To do it, proceed as
follows:
FRONT HUB
The front hub does not require any particular maintenance.For
any extraordinary maintenance and replacement of bearings,
follow these simple steps:
• Remove the contact item (A) (Fig. 1)
• On the same side from which you removed the contact item,
insert a 12mm Allen wrench (M) on the hub pin and, using
a classic 17mm wrench (N), unscrew the contact item (B)
counterclockwise (Fig. 2)
• R emove the axle from the side of the disc brake.
Once the axle has been removed, you can replace the bearings:
• Use a special puller for 17mm holes and remove both bea-
rings (S) from their seat (Fig. 3)
Once these have been replaced, proceed fitting the new be-
arings:
• Using a special tool, insert both new bearings in their seat,
checking the correct smoothness.
• I nsert the hub axel (C) again and tighten the contact item (B)
with the 17mm wrench (N) at the tightening torque of 15Nm.
(Fig. 2)
If necessary adjust the hub by working on the ring (F) (Pic. 2):
• U nlock the grub screw (I) with a allen wrentch 2mm (L).
• T urn the ring in clockwise to drop the sliding, and in counter-
clockwise to rise the sliding.
• L ock the grup screw (I) (Pic.2).
• C heck the sliding of the wheel.
Please check that the hub is correctly tightened and closed,
failure to do so could lead to a serious or fatal accident.
Warning
!
Use original spare parts exclusively provided by
Fac Michelin S.r.l. Any modification or alteration (also
graphic) of the product with non-original spare parts or
spare parts not delivered directly by Fac Michelin S.r.l., in-
volves the expiration of the guarantee.
8 REVOX WR DX / MICHE.IT
Front hub
26x17x5 (6803)
26x17x5 (6803)
REAR HUB
For any maintenance:
• I nsert allen wrentch 12mm (M) on right side of the hub (Pic. 4).
• U sing adjustable wrentch (N), unscrew left stop (O) counter-
clockwise.
Extract the axel of rear hub with the freehub body (E). If neces-
sary at this point you can:
• C hange the bearings (S).
• Grease the cogs with low density grease.
Extract from the axel the freehub body with the relative spacer
(Z) continue the cleaning process of hub. Warning: the bea-
rings of the freehub body and no replaceable.
• O nce ended the manteinance, fit back the free hub body on
the axle together with it' s spacer (Z) (Pic. 5)
• R e-fit the axel (C) inside hub body with the spacer (Z). Take
care to position of the pawls (Pic.4).
• I nsert allen wrentch 12mm (M) on right side of the hub (Pic.6).
• S topping left stop (O) with adjustable wrentch (N) locking at
15 Nm (Pic. 6)
If necessary adjust the hub by working on the ring (H) (Pic. 6):
• U nlock the grub screw (I) with a allen wrentch 2mm (L) (Pic.
6).
• T urn the ring in clockwise to drop the sliding, and in counter-
clockwise to rise the sliding.
• L ock the grub screw (I) (Pic.6).
• C heck the sliding of the wheel.
Please check that the hub is correctly tightened and closed,
failure to do so could lead to a serious or fatal accident.
Warning
!
Use original spare parts exclusively provided by
Fac Michelin S.r.l. Any modification or alteration (also
graphic) of the product with non-original spare parts or
spare parts not delivered directly by Fac Michelin S.r.l., in-
volves the expiration of the guarantee.