Operation And Maintenance - GRAPHITE 58G013 Manual De Instrucciones

SELECTION OF WORKING TOOL
With this cordless multi tool you can use working tools
compatible with universal, open attachment system (with 9
holes). Holes, 2 mm in diameter, are located around 10 mm
radius circle every 30° (some holes can also form an open cut
out).
Below table presents examples of various working tools.
Name Type of material
HSS blade Metal (e.g.
for metal bolts, small
tions), non-ferrous
metals
H a l f - r o - Wood, wood-based
und HCS materials, plastics
wheel for
wood
HCS blade Wood, wood-based
for wood materials, plastics
H a l f - r o - Cement joints, soft
und wheel ceramic tiles, hard
with tung- plastics and other
sten grit materials.
Delta san- Wood, wood-based
ding pad materials, abrasive
materials.
Stiff scra- Linings, floors, cera-
per mic tiles.
INSTALLATION OF WORKING TOOLS
• Pull the lever for quick working tool installation (1) forward
(fig. D).
• Slide working tool between two plates of the tool holder, make
sure the holes are matched with pins of the upper washer.
• In order to allow operation in the position that is most comfortable
and safe for the operator, you can set up the working tool in the
tool holder in a position of your choice, provided that the upper
plate pins are matched with the holes (fig. E).
• Working tool should be installed with bend pointing down.
• Lower the lever for quick tool installation (1) to install the working
tool in selected position (fig. D).
Check that the tool is installed properly. Improperly or
inaccurately installed working tools can slip during operation and
cause risk for the user.
DUST EXTRACTION
Dust of some materials may be hazardous to health, like paint
coatings with lead additives, some types of wood e.g. oak or
beech or materials with asbestos. Therefore, we recommend use
of external dust extraction systems, good workplace ventilation
and use of dust-mask with particle filter.
The tool is equipped with dust extraction add-on, which should be
connected to external dust extractor, e.g. vacuum cleaner designed
for the type of produced dust.
Intended use Example
nails, Small dividing and Cutting narrow
sec- plunge cutting. sections short,
cutting joining
elements, e.g.
clamps.
Dividing and plun- Narrow plunge
ge cutting in cor- cuts in solid
ners and hard to wood, e.g. for
reach areas, near air grates.
surfaces.
Dividing and plun- Cut outs in fur-
ge cutting in cor- niture boards,
ners and hard to cutting cove
reach areas, near bases short,
surfaces. plunge cutting
for fitting floor
panels.
Cutting short and Removal of
cutting off close to joint, cutting
edges, in corners holes in cera-
and hardly acces- mic tiles and
sible places. plastics.
Sanding in hard to Removal of
reach areas and in mortar and
corners on a hard glue for ce-
substrate. ramic tiles,
sanding solid
wood, poli-
shing.
Scraping soft ma- Removal of
terials on a hard mortar resi-
substrate. dues, glue for
lining or cera-
mic tiles.
REMOVING THE DUST EXTRACTION ADD-ON
• Remove working tool if already installed.
• Disengage the clamp (3) and remove the dust extraction add-on
(6).
Installation of the dust extraction add-on (6) is similar to
deinstallation, only the sequence of actions is reversed.
OPERATION / SETTINGS
Check condition of the working tools before using the power tool.
Do not use tools with dents, cracks or other damages. Replace
worn out tools with new ones before operation. When the work
is finished, always turn the device off and wait until the working
tool comes to complete stop. Only then you can put the device
away. Do not brake the working tool when it's moving by pressing
it against processed material.
SWITCHING ON / OFF
Hold the device with both hands when starting up and during
operation.
Switching on – slide the switch (2) forward to position I.
Switching off – slide the switch (2) backward to position O (fig. F).
Each time you press the switch button (2) two LED diodes (13) turn
on. They are located on both sides of the head and illuminate the
work place.
ROTATIONAL SPEED CONTROL
Wheel for rotational speed control (4) is located at the bottom part
of the main handle (fig. G). Control range is 1 to 6. Rotational speed
can be adjusted to the user's needs.
Do not cover holes for motor ventilation in the tool body.
PRINCIPLES OF OPERATION
Oscillation frequency 5 000 – 20 000 per minute at 3° angle allows to
work precisely in small areas and corners with the power tool.
OSCILLATION FREQUENCY 5 000 – 20 000 PER MINUTE AT 3°
ANGLE ALLOWS TO WORK PRECISELY IN SMALL AREAS AND
SAWING AND CUTTING
Use only undamaged working tools in good technical condition.
When sawing or cutting wood, fibre board, wood-based materials
etc. make sure they do not contain foreign objects like nails, bolts
etc. before starting the task. Remove foreign objects or use proper
blade for removal. You can make plunge cuts only in soft materials
like wood, gypsum boards and alike. Cutting ceramic tiles causes
faster wear of working tool.

OPERATION AND MAINTENANCE

Remove the battery from the device before commencing
any activities related to installation, adjustment, repair or
maintenance.
MAINTENANCE AND STORAGE
• Cleaning the device after each use is recommended.
• Do not use water or any other liquid for cleaning.
• Clean the device with a dry cloth or blow through with
compressed air at low pressure.
• Do not use any cleaning agents or solvents, since they may
damage plastic parts.
• Clean ventilation holes in the motor casing regularly to prevent
device overheating.
• Always store the tool in a dry place, beyond reach of children.
• Store the device with the battery removed.
All defects should be repaired by service workshop authorized by
the manufacturer.
14