GRAPHITE 58G036 Manual Del Usuario página 11

EQUIPMENT AND ACCESSORIES
1. Garbage bag - 1 pc.
2. Blow nozzle - 1 pc.
3. Suction nozzles - 2 pcs.
4. Wheels - 1 set.
5. Screws - 2 pcs.
PREPARATION TO WORK
ASSEMBLY / DISASSEMBLY OF BLOWING NOZZLE
• Attach the blower nozzle (1) to the blower by inserting it onto the
socket until the nozzle lock button (2) engages (fig. A).
• When disassembling the airflow nozzle (1), press the nozzle lock
button (2) and remove the airflow nozzle (1) from the connector
(Fig. B).
ASSEMBLY OF VACUUM CLEANER SUCTION PIPES
• Unscrew the fastening screw on the base of the running wheels
(11) (Fig. C).
• Install the wheels (11) by sliding them onto the guide of the front
suction tube (7) (Fig. D) and fasten with the unscrewed screw (Fig.
E).
• Connect the lower (7) and upper (8) suction tubes (fig. F) and
secure on both sides with the screws supplied (fig. G).
• Unlock and pull off the lid (9) by sliding the lid lock button (12)
(fig. H).
• Install by inserting the upper suction tube (8) into the catch (fig. I)
and engage it after pulling the catch (fig. J).
• Disassembly of the suction system is performed in the reverse
order of assembly.
ASSEMBLY / DISASSEMBLY OF THE WASTE BAG
• Clip the snap hook of the garbage bag (13) into one of the holes
in the lower nozzle (7) (fig. K).
• Slide the waste bag holder (10) over the socket and press it until
the locking button (2) audibly engages (fig. L).
• To disassemble the rubbish bag (10), press the locking button (2)
and unclip the carabiner (13).
ATTENTION! Do not start work until the assembly of the
garbage bag is complete.
OPERATION / SETTINGS
ON / OFF
WARNING! Install the batteries prior to commissioning. The
device requires 2 batteries, otherwise it will not work. In order
for the device to work properly, the batteries should have the
same capacity and charge level.
WARNING! Before starting, make sure that the switch is in the
off position and that all components are properly assembled as
described in this manual.
Turning on - press the switch button (3) (fig. M).
Switching off - press the switch button (3) again.
AIRFLOW
• With the front of the blowing nozzle approximately 18 cm above
the ground, turn on the device.
• Direct the airflow forward and slowly work your way through
leaves and debris in front of you.
• When the leaves / rubbish form a pile, switch the device to the
vacuum cleaner function and collect it.
WARNING! When starting and working, always hold the lawn
vacuum cleaner firmly with both hands using the handle.
SUCTION
• Install a garbage bag.
• Keep the suction tube just above the leaves / rubbish.
• Switch on the vacuum cleaner and, oscillating left and right, suck
the waste into the suction tube, where it will be shredded and
placed in a rubbish bag.
EMPTYING THE WASTE BAG
ATTENTION! If the filling level in the trash bag is high, the
suction power is significantly reduced.
In order to empty the filled trash bag, it is not necessary to
disassemble it.
• Open the lock on the dust bag (10) and empty the waste.
• Close the zipper on the dust bag (10).
SPEED KNOB
The garden vacuum cleaner allows you to work with different
blowing / suction force. The adjustment is made with the rotational
speed knob (4) in the range 1 - 6 shown on its circumference. To set
the desired blowing / suction force, turn the speed knob (4) to the
correct position (fig. M).
The correct selection of the blowing / suction force is carried out
during operation without the need to turn off the device.
ATTENTION! Do not use high blowing / suction force unless
necessary.
CARE AND MAINTENANCE
WARNING! Before commencing any installation, adjustment,
repair or maintenance activities, remove the batteries from the
device.
CLEANING
• It is recommended to clean the device after each use.
• The motor housing should be dust and dirt free at all times.
• Wipe the device with a clean cloth or blow it with compressed air
at low pressure.
• Do not use water or chemical cleaners for cleaning
• Be careful not to let water get inside the device.
• After finishing work, remove the garbage bag, shake it out and
clean it thoroughly to prevent the formation of mold and
unpleasant odors.
• Heavily soiled garbage bag should be emptied, washed in warm
soapy water and dried thoroughly.
• If the lock is difficult to open, coat the teeth with soap.
• If dirty, clean the suction tube with a brush.
MAINTENANCE AND STORAGE
• Make sure the screws are properly tightened so that you can work
safely.
• Check the garbage bag for wear and deformation.
• Use only original accessories and original spare parts.
• When not in use, the device should be stored in a dry place out of
the reach of children.
All kinds of faults should be removed by the manufacturer's
authorized service.
10