Descargar Imprimir esta página

Fontanot CUBE TUBE Instrucciones Para El Ensamblaje página 7

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 12
which do not provide for railing, insert sections of column C81 which have been cut to size. Close the sides of
the column with articles C74 (fig. 11).
21. Check the verticality of all of the balusters (C67) positioned. Take care during this operation because it is very
important to assembling the staircase correctly.
22. Tighten element C70 permanently (fig. 8).
23. Tighten tread element B02 in a permanent manner. Assemble elements C72 on the treads (L30) (determine
the position of the openings using the template provided) with articles C57 and B02 and drill using a Ø 4.5 mm
point (fig. 2).
24. Check the verticality of the balusters (C67) again and correct by repeating the operations described above, if
necessary.
25. Position the "X" initial baluster (C67). Adjust the height of a long baluster (C67) cutting the end to the same
height as those already assembled (fig. 1).
26. Fasten element F34 to the floor near the first baluster (C67), drill using a Ø 8 mm point. Use elements C58,
B12, B83 and B02 (fig. 1).
27. Cut sections of handrail BH4 to length; assemble with part B51. For optimal fixing, the handrail must follow
about 1/8 of a turn from the contact point (fig. 1).
28. Fix handrail to balusters with parts CD3; keep balusters vertical. Insert angle parts BG4, BG2 and BG3 with
screws BB3 and BB6 for changes of direction. Apply end caps BG4 to ends of handrail with parts BH6 and B08
(fig. 1).
29. To further stiffen the staircase at intermediate points, secure elements F09 to the wall and join using elements
F33, with the balusters (C81 or C67). Drill using a Ø 8 point and use elements C50, C49, C58, B12 (fig. 11).
30. Determine the length of the bars A28 based on the staircase dimensions and cut them. Insert the bars A28
in the parts D39 previously assembled on the "Y" C67 intermediate balusters and in the parts D75 previously
assembled on the "X" C67 end balusters (fig. 1a) (fig. 3-3a). Join the bars A28 to each other using the part A41
and the glue provided (fig. 1a). Finally, tighten the parts C76 on the part D75 (fig. 1a).
Assembling the railing on the landing and the supplementary balustrade
31. Assemble the column (C73) on element G01 protruding from the landing (E02), positioning articles D75 towards
the outside, using elements D49 (fig. 8) (fig. 9) (fig. 1).
32. Position elements F34, using elements C58, B83, B02 on the landing (E02). Drill the landing (E02) using a
Ø 5 mm point, maintaining the same centre to centre distance between the holes as the one used between the
balusters (C67) of the railings assembled before.
33. Position the "X" end balusters and the "Y" intermediate (C68) balusters with the D75 and D39 elements placed
outwards and tighten the elements B02 of the articles F34 (fig. 1) (fig. 3a).
34. Cut 5cm off the straight handrail BH4. Drill a hole in the top using a 3.5mm Ø point and assemble the parts
BG4, BG3 with the screw BB3 (fig. 1).
35. Fit the assembly obtained with the elements BD2, BG2, BH1 and BG8 on the element C73 and tighten with the
dowel BC3 (fig. 1). Assemble the straight handrail BH4 on the element C73 and tighten with the element BB6
(fig. 1).
36. Cut the other end based on the dimensions of the balustrade, drill a hole using a 6 mm Ø bit to fasten the part
BG4 or drill a hole using a 3,5 mm Ø bit to fasten the parts BG2+BG3 with the parts BB3. Fasten the handrail
BH4 using the parts CD3, checking that the balusters are vertical. Tighten the parts B02 (fig. 1).
37. Determine the length of the bars A28 based on the dimension of the balustrade and cut them (fig. 1).
38. Based on the position and the existence of walls around the opening of the staircase, one or two (C03) extra
balusters may need to be positioned (fig. 9).
39. In this case, consider a space equidistant from the other balusters or from the wall. To secure these, we
recommend drilling the landing (E02) with a Ø 5 mm point and using elements F34, C58, B83, B02. We also
recommend drilling the floor with a Ø 14 mm point and using elements F34, B02, B13 (fig. 10).
7 - CUBE TUBE L

Publicidad

loading