Requirements For The Floor Plate; Position Of Theappliance; Assembly Prior To Installation; The Vent System - Jøtul GF 3 CF Instrucciones Para Instalación

Requirements for the floor plate

The appliance may stand on a wooden floor. A floor plate
of non-combustible material is required if the appliance is
to be placed on carpet, vinyl, linoleum or other combustible
material. Minimum dimensions of the floor plate: 580 x
435mm. Jøtul can supply floor plates in blue black enamel
for the Jøtul GF 3 CF (see section about optional
equipment).
Position of the appliance
Minimum clearances are as follows: (fig. 1)
• Clearance from wall to rear of appliance, (fig. 1-B).
• Clearance from wall to side of appliance ( fig. 1-A).
Note! The right side requires at least 250mm(10") for
the operation of control knobs for lighting.
• Clearance from corner to appliance, (fig. 1-C).

Assembly prior to installation

The product is delivered in 2 packages - the stove and a
coal kit or a ceramic logset.
Included in the fire box:
• The instruction booklet.
• A convertion kit for LPG and Natural Gas G 25.
Mounting
• When the product has been unwrapped, lift off the top.
•
Take out the parts wrapped in plastic under the top
plate. (A small and a large cover for the flue outlet)
• Lift the glass frame with the glass straight up by opening
the 2 latches at the top of the fire box.
• Remove the parts wrapped in plastic inside the stove.
If the product is going to be used with another type of
gas than G20 natural gas, it should be converted now.
See the manual for the conversion kit.
• Unwrap the box containing the log set/coal set. The
box contains also a burner.
Mounting of the burner
• Follow the installation instructions which are included
with the burner/ coal set or log set.
• After mounting - put the glasframe down back in its
track, and be particular about mounting the top plate
correctly on its mountings.
• When installing a top flue outlet, the small flue outlet
cover is to be placed on the rear of the flue pipe.
• When installing a rear flue outlet, the large cover has to
be put in place in the top plate
• Install the ash lip by hooking it onto the front, just below
the front frame. It should bear against the two cams
on each side of the front frame.
All manuals and user guides at all-guides.com

The vent system

Flue outlet (spigot) dimensions:
Internally = 128 mm
Externally = approx. 131 mm
The product may also be installed using 100 mm (4") pipe
components or approved flexible pipes. All vent pipes must
be installed according to approval and the instructions of
the manufacturer.
When installing the vent, it is important to adhere to
national and local regulations that apply. Only one fireplace
may be connected to the vent system.
The vent system must terminate above the roof.
The vent system and the flue pipe components must be
fastened to the stove with screws.
Minimum height of the chimney is approx. 2,15 m (7') and
maximum height should not be more than approx. 10,7 m
(35'). (When installation is at or above a height of approx.
610 m (2000'), the chimney's height must be at least approx.
3,7 m (12'.) measured from the flue outlet.
If the chimney has to move through a horizontal distance,
make sure to use 45
Max. number of 45
Max. number of 90
It is permitted to move the chimney a total of approx. 1,2 m
(4')horizontally.
An exhaust hood (terminal, cowl or rain cap) must be
mounted at the chimney's termination point (fig. 1-d).
After fitting of the vent system and installation of the
appliance, carry out a smoke test on the flue as described
in the relevant section.
If the appliance shuts off in operation for no apparent reason
(especially during windy or stormy conditions) and will not
relight, it is possible that the flue system safety switch has
operated. Allow the appliance to cool down and relight. Any
obstruction to the flow of exhaust gases up the flue can
cause this switch to operate thereby making the situation
safe. If the appliance cuts out repeatedly, do not continue to
use the appliance and seek flue checking and service from
qualified personnel before re-using the appliance.
Closure Plate Installation (fig. 1 E-F)
It is permissible to install this appliance using a closure
plate installation similar to traditional outset gas fires. See
diagrams (1 E-F) on page 56. The British Standards detailing
this type of installation are BS5871 pt1 and BS5440 pt 1.
The fireplace and flue must be sound and if used with solid
fuel or oil appliances it must be swept prior to installation.
There must be no other openings other than the exit from
the top of the flue and the opening into which the appliance
is being installed. All cracks, holes, underfloor air vents etc
must be removed and sealed fully before installation
continues. A proprietary metal flue box complying with BS715
is a suitable fireplace opening.
ENGLISH
or 90 bends (fig. 3).
0 0
0 bends = 4
0 bends = 3
15