INSTALLATION INSTRUCTIONS
1
11
15
Cut 2'' - 3''
Couper 2'' - 3''
Corte 2"- 3" (5 cm - 7.5 cm)
13
MOUNTING SHANK
PLUMBER'S PUTTY
TIGE DE MONTAGE
MASTIC DE PLOMBIER
CAÑA DE MONTAJE
MASILLA DE PLOMERO
CAUTION: See template above for roll pin location. Drill a 7/32" hole into
!
tub base. Install spout escutcheon (13) with roll pin.
CAUTION: Remove burrs and bevel end of shank. Failure to do so may
!
result in damaged spout o-ring during spout installation.
1. Apply a bead of plumber's putty (not provided) under the bottom of the
spout escutcheon (13). Using the silicone grease packet (supplied),
apply the silicone grease to the spout mounting shank pictured above.
Place the spout escutcheon over the mounting shank and onto the
deck and install roll pin (15). With the roll pin in place, assemble the
spout (11) onto the mounting shank by engaging the mounting shank
into the spout, then lowering the spout onto the spout escutcheon.
Install the set screw (10) and secure the spout to the deck with a 5/32"
hex wrench (provided) by applying a slight downward pressure to the
spout, and rotating the hex wrench clockwise until the spout is firmly
seated against the spout escutcheon.
NOTE: The aerator is pre-assembled into the spout
4
4. Hot/Cold Temperature Indicator Installation (OPTIONAL)
If the temperature indicators are desired on your faucet,
installation is as follows:
a. Remove the handle hub (6) from the lever or knob handle (1) by
grasping the handle hub in one hand and separating the handle
from the handle hub with the other hand.
b. Install the RED (HOT) temperature indicator onto a handle
assembly by aligning the indicator slots with the chassis (2) tabs,
then sliding the temperature indicator over the chassis until it
makes contact with the handle.
c. Re-assemble the handle assembly with temperature indicator into the
handle hub, making sure that the chassis tabs align with the handle
hub slots. Push the handle hub onto the chassis until it stops.
d. Repeat the above steps for installing the BLUE (COLD)
temperature indicator onto the other handle assembly.
.730 (19MM)
(FRONT)
GOUPILLE CYLINDRIQUE -
(DEVANT)
ROLL PIN
(FRENTE)
GOUPILLE CYLINDRIQUE
AGUJERO DE 7/32" (6MM) PARA
PASADOR CILINDRICO
TOP OF FINISHED SURFACE
DESSUS DE LA SURFACE FINIE
CARA SUPERIOR DE LA SUPERFICIE ACABADA
.
1
5
2
6
7
2
27/32" DIA.
14
MOUNTING SHANK
DIAM.DE LA TIGE
DE MONTAGE
21MM
16
CAÑA DE
DIA. 27/32" (21MM)
Add
7/32" DRILL ROLL PIN
ç
PER
AGE- 6 mm
PASADOR CILÍNDRICO
2. Remove phillips head screw (14)
and replace white colored stem
extension with khaki colored stem
extension (supplied with trim kit).
Temporarily place handle assembly
onto stem extension (16) making
sure that lever handles point 180°
away from spout. If handle rotation
is not at desired side, remove and
rotate stem extension 180°.
Reinstall screw (14).
5
5. Position the HOT (left) handle assembly on valve pointing away from the
spout mounting position. Holding the lever handle (1) stationary with one
hand, apply a slight downward pressure and rotate the handle hub (6)
clockwise with the other hand (Hint: to ensure correct handle installation,
rotate the handle hub counter-clockwise first until handle assembly drops
into position, then rotate the handle hub clockwise to install). Taking care
not to cross-thread, continue to tighten the handlehub by hand until it is
firmly seated against the handle escutcheon (7).
NOTE: The handle should stop in the "OFF" position when the handle is
pointing away from the spout position, and full "ON" when the handle
is pointing towards the spout. Repeat the above step for installing the
COLD (right) handle assembly.
3
16
Remove
7
3. Apply a bead of plumber's putty
(not provided) under the bottom of
the two handle escutcheons (7).
Place handle escutcheons over
each valve body, allowing them to
rest on deck. Rotate the valve
stem extensions (16) pictured
above to the "OFF" position (clock-
wise for HOT and
counter-clockwise for COLD).
7
16
Valve Stem
Extension
1
6
2