Installation Instructions - English - Moen 7700 Serie Manual De Instrucciones

INSTALLATION INSTRUCTIONS - ENGLISH

Various faucet models have slight
1
differences in installation procedures.
Please review all instructions before
installation. Go to Step 2.
2
BE SURE MOUNTING AREA IS CLEAN AND DRY
For without Spray model,
For Side Spray model only,
go to Step 3 go to Step 4
HINT: When using flexible supplies (not included), we
recommend supply lines be installed onto threaded fittings
before placing valves through sink holes. See Step 7
IMPORTANT
For deck hole depth
deeper than 1-1/8".
Install mounting bracket
with open side down
28
Thin Deck Thick Deck
Installation Installation
5. From under sink, install mounting bracket (28) over
threaded shank (26) on spout body and install mounting
nut (29) onto threaded shank. BE SURE TEE IS STILL
ALIGNED AS SHOWN IS STEP 4. Make final tightening
of mounting nut with the mounting tool (38) provided.
FOR SPRAY MODEL ONLY - Connect spray hose swivel
nut (33) onto the threaded shank on spout body (26).
8
31
32
8. From below sink, attach supply hoses
(32) by holding T-Connector (31) with
wrench. Use an adjustable wrench to
fasten supply hose nut to T-Connector.
CAUTION: DO NOT TWIST THE
TEE CONNECTOR.
11
1 2
3
5
13
14
12
3
36
3. Locate foam gasket on hose guide (36) by sliding gasket onto
shank and tucking outer edge of gasket under the hose guide
(36). Do not drive the center area of the gasket up into the hose
guide. Install hose guide (36) through hole in sink. From under
sink, thread extended locknut (37) (either side up) on shank of
hose guide and tighten by hand. Feed spray head (35) and hose
(34) down through the hose guide (36) (do not connect spray
hose to faucet until step 5 below).
5
SINK/DECK
28
26
29
29
30
SPRAY
33
MODELS
34
9
9. With a wrench, fasten ends of supply
hoses (32) to valve bodies (39) (you
may have to loop supply lines).
6 7
8
10
11
9
4
4
13
14
12
37
6
40
23
20
21
25
27
6. Carefully raise spout nut
(23). Apply silicone grease
(42) to O-ring (21) and
retaining ring (20). Install
spout (18) into spout body
(25). Thread spout nut hand
tight to secure spout.
39
32
LEVER HANDLE MODELS
Install lever handle (1) with color
ring (2) into handle hub/elbow
assembly (3,4) and hand tighten
CROSS HANDLE MODELS
Place cross handle insert (10)
onto handle skirt (9), insert han-
dle screw (7) through color ring
(8) and cross handle insert and
tighten. Install plug button (6)
over screw head.
4
35
34
36
4. Install spout deck ring (27)
onto spout valve body
(25). Attach T-Connector
(31) and orient tee ends
to face valves as pictured
above.
7
MOUNTING WASHER
39
VALVE MOUNTING NUT
OUTLET
7. Screw valve mounting nuts down the valve
bodies and drop on the mounting washers.
NOTE: CHECK STEM EXTENSIONS INSIDE
VALVE BODY FOR HOT (RED) SIDE VALVE
AND COLD (BLUE) SIDE VALVE. From under
sink, slide valve bodies up through holes. Screw
top mounting nuts down until tops of valve bodies
are 5/8" (16mm) to 11/16" (18mm) from top of
sink/deck. Position valves making sure outlets
on valves are facing in toward the T-Connector.
Hand tighten the mounting nuts under the sink.
10
10. Using a basin wrench make final tightening
of all mounting nuts (hold valve bodies from
turning using another wrench on flats of
valve bodies). Check spout alignment.
11. ALL MODELS: Insert gasket (14) into bottom of
escutcheon (13). Center escutcheon over valve
bodies. Rotate stem extensions (12) to off position:
clockwise for hot, counterclockwise for cold.
Position lever handle assembly (5) 90° away
from spout. For cross handle assembly (11),
position in desired orientation. Holding lever (1)
or cross (10) handle, hand tighten handle hub (4)
clockwise. Make connections to supply lines.
Faucet flushing is required, see faucet flushing
instructions on page 3.
25
27
31
TOP MOUNTING
NUT
5/8" (16mm)
to 11/16" (18mm)
2
continued