Declaration Of Conformity - WEG W01 Manual De Instalación, Operación Y Mantenimiento

DECLARATION OF CONFORMITY

Manufacturers:
WEG EQUIPAMENTOS ELÉTRICOS S.A.
Av. Prefeito Waldemar Grubba, 3000
89256-900 - Jaraguá do Sul – SC – Brazil
www.weg.net
WEG Linhares Equipamentos Elétricos
S.A.
Rod. BR 101, Km 161,5, s/n.
Distrito Industrial Rio Quartel. Bairro Rio
Quartel de Baixo
29915-500 – Linhares – ES – Brazil
www.weg.net
WEG MEXICO, S.A. DE C.V
Carretera Jorobas - Tula Km 3.5,
Manzana 5, Lote 1, Fraccionamiento
Parque Industrial Huehuetoca, Municipio
de Huehuetoca, C.P. 54680, CD. de
Mexico y Área Metropolitana – Mexico
www.weg.net/mx
The manufacturer declares under sole responsibility that:
W01, W11, W12, W20, W21, W22, W40, W50, W60, HGF, Roller Table, W21 Magnet, W22 Magnet , Pump/Filter and
when installed, maintained and used in applications for which they were designed, and in compliance with the relevant installation
standards and manufacturer's instructions, comply with the provisions of the following relevant United Kingdom statutory
requirements, wherever applicable:
The Ecodesign for Energy-Related Products and Energy Information (Amendment) (EU Exit) Regulations 2019 –
The Ecodesign for Energy-Related Products and Energy Information (Amendment) (EU Exit) Regulations 2020 – Part
The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012;
Electromagnetic Compatibility Regulations 2016 (electric motors are considered inherently benign in terms of electromagnetic
The fulfilment of the safety objectives of the relevant United Kingdom statutory requirements has been demonstrated by
compliance with the following designated standards, wherever applicable:
EN 60034-1:2010 + AC:2010 / EN 60034-2-1:2014 / EN 60034-5:2001 + A1:2007 / EN 60034-6:1993/ EN 60034-7:1993 +
A1:2001 / EN 60034-8:2007 + A1:2014/ EN 60034-9:2005 + A1:2007 / EN 60034-11:2004/ EN 60034-12:2017 / EN 60034-
14:2018 / EN 60034-30-1:2014/ EN 60204-1:2018 / EN IEC 60204-11:2019 / EN IEC 63000:2018 and IEC 60034-25:2018.
UKCA marking in: 2021
* Electric motors with a voltage rating higher than 1000V are not under the scope.
** Low voltage electric motors are not considered under the scope and electric motors designed for use with a voltage rating higher than 1000V
are considered partly completed machinery and are supplied with a "Declaration of Incorporation":
The products above cannot be put into service until the machinery into which they have been incorporated has been declared in conformity with
the Machinery Directive.
A Technical Documentation for the products above is compiled in accordance with Part 7 (b) of schedule 2 of The Supply of Machinery (Safety)
Regulations 2008.
We undertake to transmit, in response to a reasoned request by the national authorities, relevant information on the partly completed machinery
identified above through WEG authorized representative established in the United Kingdom. The method of transmission shall be electronic or
physical method and shall be without prejudice to the intellectual property rights of the manufacturer.
Jaraguá do Sul, March 8 , 2021
th
Signed for and on behalf of the manufacturer:
Rodrigo Fumo Fernandes
Engineering Director
Brazil
WEG (JIANGSU) ELECTRIC
EQUIPMENT CO., LTD.
No. 88, Huimin West Road, Chengbei
Street,
Rugao City, Jiangsu Province – China
www.weg.net/cn
WEG (NANTONG) ELECTRIC MOTOR
No. 128# - Xinkai South Road, Nantong
Economic & Technical Development
Zone, Nantong, Jiangsu Province – China
www.weg.net/cn
WEG electric motors and components used for following motor lines:
Electrical Equipment (Safety) Regulations 2016*;
Schedule 2-6* (valid until June 30th, 2021) and
4-15* (valid from July 1st, 2021);
Supply of Machinery (Safety) Regulations 2008**;
Declaration of Incorporation:
Edson José Koshinski
Engineering Director
China
WQuattro
compatibility).
Bruno Mauro Burdzaki
Industrial Director
Mexico
Motores Elétricos de Baixa e Alta Tensão | 3
WEGEURO – INDUSTRIA
ELECTRICA S.A.
Headquarters:
Rua Eng. Frederico Ulrich,
Zona Industrial da Maia Sector V
4470-605 – Maia – Portugal
www.weg.net/pt
Branch – Santo Tirso:
Rua António Joaquim Campos
Monteiro, 510
Santa Cristina do Couto
4780-165 – Santo Tirso – Portugal
www.weg.net/pt
WEG UK CONTACT:
Contact person: Patrick O'neill
Authorised Representative in the
United Kingdom
(Single Contact Point)
Luis Filipe Araujo
Industrial Director
Portugal