Reclining Adjustment; Height Adjustment For Head Support And Shoulder Harness Straps; Infant Mode; For Child Under 18Kg / Newborn - 4 Years Old - Joie stages Manual De Instrucciones

Reclining Adjustment

- 1
Squeeze the reclining adjustment handle 4
The recline positions are shown in .
5
There are three recline positions (1-3) for forward-facing Toddler mode and two recline positions (1-2) for
forward-facing Youth mode . The recline position 4 is for rearward-facing Infant mode
5
Angle indication: with top and bottom triangles aligned
Height Adjustment
(for Head Support and Shoulder Harness Straps)
Please adjust the head support and shoulder harness straps to the proper height according to the child's
height.
! When used in rearward-facing Infant mode, the shoulder harness slots must be even with or just
- 1
below the child's shoulders. 6
! When used in forward-facing Toddler mode, the shoulder harness slots must be even with or just
- 2
above the child's shoulders. 6
! When used in forward-facing Youth mode, the shoulder belt guides must be even with or just
- 3
above the child's shoulders. 6
If the shoulder harness straps are not at proper height, the child may be ejected from the car seat during
a crash.
Squeeze the head support adjustment handle
snaps into one of the five positions.
The head support positions are shown in 7 .

Infant Mode

(for Child under 18kg / Newborn - 4 years old)

Reference age Newborn - 4 years old
Seat position
Position 4 (with top triangle and blue triangle aligned, as shown in
! Please install the car seat on the vehicle seat first, and then place the child in the car seat.
i. Installation for Rearward-Facing Infant Mode
Note
1. First adjust the car seat to recline Position 4. Angle indication: With top triangle and blue triangle
aligned . Please refer to Page 13 (Reclining Adjustment).
5
2. Make sure the shoulder harness straps are adjusted to the proper height before installing this car
seat. Please refer to Page 13

(Height Adjustment for Head Support and Shoulder Harness Straps).

3. When installing and adjusting the vehicle belts, make sure that both the vehicle shoulder belt and the
vehicle waist belt are not twisted or the belts may not function properly.
1. Remove infant body support.
! Vehicle waist belt must pass underneath infant body support.
15
- 2
, and adjust the car seat to the proper position 4
5
.
.
5
- 1
7 and pull up or push down the head support until it
5 ).
2. Pass the vehicle waist belt
buckle tongue into the buckle
3. Install the vehicle shoulder belt
.
the seat shell
Vehicle shoulder belt must pass through the rear-facing vehicle shoulder belt slots.
!
4. While pressing the car seat down firmly into the vehicle seat
fasten the car seat tightly and securely
! Please check if car seat is installed tightly by moving the car seat back and forth at the vehicle
belt path. Please reference vehicle owner's manual for more information.
(Car Seat should not move more than 25mm/1").
Correctly assembled vehicle belt is shown in
Vehicle waist belt passes through the vehicle waist belt slots, as show in
!
! Vehicle shoulder belt must pass through the rear-facing vehicle shoulder belt slots,
as shown in
! The vehicle buckle tongue is engaged with the buckle correctly, as shown in
ii. Securing your Child in the Car Seat
Note
1. Infant body support is for child's protection. Child 0-6 months must use infant body support.
2. Please install the car seat on the vehicle seat, and then place the child in the car seat.
3. After the child is placed into the car seat, check whether the shoulder harness straps are at the
proper height. Please refer to
Harness Straps).
1. Pull up the webbing lock
- 2
length. 13
2. Press the red button down to disengage the buckle.
3. Place the infant body support in the car seat, and then leave the harness straps on the left and right
sides of the car seat.
4. Place the child in the car seat and pass both arms through the harness straps.
! After the child is seated, double check whether the shoulder harness straps are at the proper
height. Please refer to Page 13 (Height Adjustment for Head Support and Shoulder
Harness Straps).
5. Engage the buckle.
6. Pull down the adjustment webbing and adjust the harness so that your child is snugly secured.
! Make sure the space between the child and the shoulder harness strap is about the thickness of
one hand.
- 1
8 through the vehicle waist belt slots and then engage the vehicle
9 .
- 2
8 in the two rear-facing vehicle shoulder belt slots at the back of
10 .
- 1
11
- 2
.
11
.
12
- 2
12 .
Page 13 (Height Adjustment for Head Support and Shoulder
- 1
13 , while pulling out the shoulder harness straps to the proper
14
15
17
18
, pull the vehicle shoulder belt to
- 1
.
12
- 3
.
12
16
18
16