Tabla De Contenido; Before Using; Cautions On Installation; Cautions On Handling - Denon DRA-295 Instrucciones De Operación

2 We greatly appreciate your purchase of the DRA-295.
2 To be sure you take maximum advantage of all the features DRA-295 has to offer, read these
instructions carefully and use the set properly. Be sure to keep this manual for future reference
should any questions or problems arise.
"SERIAL NO.
PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO THE REAR OF
THE CABINET FOR FUTURE REFERENCE"
2 INTRODUCTION
Thank you for choosing the DENON AM-FM Stereo receiver. This remarkable component has been engineered
to provide outstanding high fidelity reproduction of your favorite music sources.
As this product is provided with an immense array of features, we recommend that before you begin hookup and
operation that you review the contents of this manual before proceeding.
TABLE OF CONTENTS
z
Before Using .......................................................3
x
Cautions on Installation .......................................3
c
Cautions on Handling ..........................................3
v
Features ..............................................................3
b
Part Names and Functions ..................................4
n
Connections ....................................................5, 6
m
Using the Remote Control Unit...........................7
2 ACCESSORIES
Check that the following parts are included in addition to the main unit:
q Operating instructions.................................1
w Service station list ....................................1
e Remote control unit (RC-907) .....................1
r R6P/AA batteries .......................................2
e r

1 BEFORE USING

Pay attention to the following before using this unit:
• Moving the set
To prevent short circuits or damaged wires in the
connection cords, always unplug the power cord and
disconnect the connection cords between all other
audio components when moving the set.
• Before turning the power operation switch on
Check once again that all connections are proper and
that there are not problems with the connection cords.
Always set the power operation switch to the
standby position before connecting and disconnecting
connection cords.
All manuals and user guides at all-guides.com
,
Operation ......................................................7 ~ 9
.
Listening to the Radio.................................9 ~ 12
⁄0
Last Function Memory ......................................12
⁄1
Initialization of the Microprocessor ...................12
⁄2
Troubleshooting ................................................13
⁄3
Specifications ....................................................13
t AM loop antenna .......................................1
y FM indoor antenna ....................................1
u FM antenna adapter .........................................1
t y u
• Store this instructions in a safe place.
After reading, store this instructions along with the
warranty in a safe place.
• Note that the illustrations in this instructions may
differ from the actual set for explanation purposes.

2 CAUTIONS ON INSTALLATION

Noise or disturbance of the picture may be generated
if this unit or any other electronic equipment using
microprocessors is used near a tuner or TV.
If this happens, take the following steps:
• Install this unit as far as possible from the tuner or
TV.
• Set the antenna wires from the tuner or TV away from
this unit's power cord and input/output connection
cords.
• Noise or disturbance tends to occur particularly when
using indoor antennas or 300 Ω/ohms feeder wires.
We recommend using outdoor antennas and 75
Ω/ohms coaxial cables.
For heat dispersal, leave at least 10 cm of space
between the top, back and sides of this unit and the
wall or other components.

3 CAUTIONS ON HANDLING

• Switching the input function when input jacks are
not connected
A clicking noise may be produced if the input function
is switched when nothing is connected to the input
jacks. If this happens, either turn down the MASTER
VOLUME control or connect components to the input
jacks.
• Muting of HEADPHONE jack and SPEAKER
terminals
The HEADPHONE jack and SPEAKER terminals
include a muting circuit. Because of this, the output
signals are greatly reduced for several seconds after

4 FEATURES

1. Powerful, Versatile Amplifier
High-Quality Power Amplifier:
High-speed, high-power transistors employed in a
rational circuit configuration reflect DENON'S
advanced amplifier technology and ensure a very
hefty, clean power output.
2. Signal Level Divided Construction (SLDC)
The circuits handling low-level and high-level signals
have been divided into separate blocks to ensure
that influences from these signals on each other
are held to an absolute minimum. This chassis
design in this unit is called the Signal Level Divided
Construction (SLDC). Signals for output are cleaner
than before, allowing them to be reproduced with
even greater fidelity and clarity.
ENGLISH
10 cm or more
B
10 cm or more
the power operation switch is turned on or input
function, surround mode or any other set-up is
changed.
If the volume is turned up during this time, the output
will be very high after the muting circuit stops
functioning. Always wait until the muting circuit turns
off before adjusting the volume.
• Whenever the power operation switch is in the
OFF or STANDBY state, the apparatus is still
£
connected on some AC line voltages.
Please be sure to unplug the cord when you leave
home for, say, a vacation.
3. Remote Control Functions
The Remote Control (RC-907) commands not only
the receiver but can also operate the main
functions of a DENON CD player and a cassette
deck.
wall
3