Connections - Denon DRA-295 Instrucciones De Operación

6 CONNECTIONS

• Do not plug in the power cord until all
connections have been completed.
• Be sure to connect the left and right channels
properly (left with left, right with right).
• Insert the plugs securely. Incomplete
connections will result in the generation of noise.
• Use the AC OUTLET for audio equipment
only. Do not use them for hair driers, etc.
Connecting the audio components
OUTPUT
R L
R L
AUDIO
R L
IN
CD
LOOP
AM
ANT.
L
DVD/ VDP
R
FM
COAX. AUX
75
CDR L
ANTENNA TERMINALS
L
R
TAPE
R
CDR L
R
TAPE
OUT
R L
L
R
AUDIO IN
Tape deck
R L R L
R L R L
OUTPUT INPUT
CD recorder
R L R L
B
R L R L
OUTPUT INPUT
Connecting a tape deck
Connections for recording:
Connect the tape deck's recording input jacks (LINE IN
or REC) to this unit's tape recording (OUT) jacks using
pin plug cords.
Connections for playback:
Connect the tape deck's playback output jacks (LINE
OUT or PB) to this unit's tape playback (IN) jacks using
pin plug cords.
All manuals and user guides at all-guides.com
• Note that binding pin plug cords together with
power cords or placing them near a power
transformer will result in generating hum or other
noise.
• Noise or humming may be generated if a
connected component is used independently
without turning the power of this unit on. If this
happens, turn on the power of the this unit.
CD player
Connecting a CD player
DIGITAL AUDIO DIGITAL AUDIO
Connect the CD player's output jacks to this unit's
CD jacks using pin plug cords.
AC OUTLET
SPEAKER SYSTEMS
B A
R L R L
AC 230V 50Hz
SWITCHED
100W MAX.
SPEAKER IMPEDANCE
A OR B / 4 16
A + B / 8 16
Connecting the AC OUTLET
AC OUTLET
• SWITCHED (capacity – 100 W)
The power to these outlets is turned on and off in conjunction
with the power operation switch on the main unit, and when the
power is switched between on and standby from the remote
control unit.
No power is supplied from this outlet when this unit's power is
at standby. Never connect equipment whose capacity is above
100 W.
NOTE:
Only use the AC OUTLET for audio equipment. Never use them
for hair driers, TVs or other electrical appliances.
Connecting the antenna terminals
DIRECTION OF
BROADCASTING
FM ANTENNA
STATION
75 Ω/ohms
COAXIAL
CABLE
FM ANTENNA
ADAPTER
(An Accessory)
FM INDOOR ANTENNA
(An Accessory)
FM ANTENNA
ADAPTER
(An Accessory)
AC CORD
AC 230 V, 50 Hz
AM loop antenna assembly
1 2
Remove the vinyl tie
and take out the
connection line.
4
a. With the antenna
on top any stable
surface.
Mount
b. With the antenna
attached to a wall.
Installation hole Mount on wall, etc.
AM LOOP
ANTENNA
(An Accessory)
FEEDER
CABLE
AUDIO
L
R
IN
CD
LOOP
AM
ANT.
DVD/ VDP
FM
COAX. AUX
75
CDR
ANTENNA TERMINALS
TAPE
AM OUTDOOR
300 Ω/ohms
ANTENNA
CDR
TAPE
L OUT
R
300 Ω/ohms
TERMINAL
GROUND
FM antenna adapter assembly
Connect to the AM
antenna terminals. Open the Cover
3
PULL
PULL
Bend in the reverse CLAMP
direction.
ANTENNA ADAPTER
REMOVE
CLAMP
Connection of AM antennas
1. Push the lever. 2. Insert the
NOTES:
• Do not connect two FM antennas simultaneously.
• Even if an external AM antenna is used, do not
disconnect the AM loop antenna.
• Make sure AM loop antenna lead terminals do
not touch metal parts of the panel.
ENGLISH
75 Ω/ohms COAXIAL CABLE
SHUT
CLAMP
3C-2V 5C-2V
3. Return the lever.
conductor.
5