Publicidad
Idiomas disponibles
Idiomas disponibles
EN
Plate position-beneath framed recessed cabinet
bottom
NOTE:
IT IS VERY
READ
AND FOLLO
IMPOR
IN THE
INSTAL
W THE
TANT
TO
BEFOR
E PROCE
LATION
DIREC
TIONS
REAR
EDING
INSTR
UCTIO
This Rear
WALL
TEMPL
WITH THIS
NS
3/8" TO EDGE
mounting
Wall Template
ATE.
12"
outlet.
plate and
to locate
serves
to position
1. Use
a level
the horizontal
the bottom
exhaust
accurately
.
to check
that the
2. Locate
and mark
template
is positioned
right side
of the centerline
at least
one stud
4"
screw mounted
It is important
.
on the left
or
of the microwav
firmly in
to use at
least one
locations
e. Mark
a stud to
support
wood
3. Drill holes
for the supplied
two additional
, evenly
the weight
a stud,
drill a 3/16"
in the marked
toggle bolts.
locations.
spaced
that do
not line
hole for
wood screws.
Where
there is
toggle bolts.
up with
a stud,
For holes
DO NOT
drill 5/8"
holes for
4. Remove
AT THIS
TIME.
INSTALL
THE MOUNTIN
5. Review
the template
G PLATE
installatio
the Installatio
from the
rear wall.
n situation.
n Instruction
book for
your
Darle vuelta
versión
a la hoja
en Español.
para consulta
r la
Locate
and mark
mounti
ng plate.
holes to
IMPOR
align with
holes in
TANT:
the
LOCAT
E AT LEAST
THE CENTE
ONE STUD
MARK
RLINE.
ON EITHER
SPACE
THE LOCAT
SIDE OF
D TOGGL
ION FOR
2 ADDIT
AREA.
E BOLTS
IONAL
IN THE
MOUN
, EVENL
Y
TING PLATE
Trim the
rear wall
templa
te along
the dotted
line.
Locate
and mark
mounti
IMPOR
ng plate.
TANT:
LOCAT
E AT LEAST
THE CENTE
MARK
RLINE.
THE LOCAT
SPACE
D TOGGL
AREA.
C
Draw a vertical line on the wall at the center of the 24"
space.
Tape the Rear Wall Template onto the wall
matching the centerline and touching the bottom
cabinet frame.
D.
ALIGNING THE WALL PLATE
CAUTION: Wear gloves
to avoid cutting fingers on
sharp edges.
1. Draw a vertical line on the wall at the center of the 24"
wide space.
3. Find a wall stud in area "E" of mounting plate Refer to
section 1B. Finding the wall studs.
4. For attaching the mounting plate into stud drill a 3/16"
hole into wood stud. Drill a 5/8" hole for toggle bolt in
1 other location (Hole A or Hole B)
NOTE: DO NOT MOUNT THE PLATE AT THIS
TIME.
1/4"
Minimum
clearance
Trim the
rear wall
templa
te along
the dotted
line.
holes to
align with
holes in
the
ONE STUD
ON EITHER
SIDE OF
ION FOR
E BOLTS
2 ADDIT
IONAL,
IN THE
MOUN
EVENL
Y
TING PLATE
30" to Cooktop
Hole B
Area E
Your cabinets may have decorative trim that interferes
with the microwave installation. Remove the decorative
trim to install the microwave properly and to make it
level.
THE MICROWAVE MUST BE LEVEL.
Use a level to make sure the cabinet bottom is level.
If the cabinets have a or front filler piece. only, with no
back or side frame, install the mounting plate down the
same distance as the front overhang or front filler piece
thickness. This will keep the microwave level.
1.Measure the inside depth of the front overhang.
2.Draw a horizontal line on the back wall an equal
distance below the cabinet bottom as the inside
depth of the front overhang.
3.For this type of installation with front overhang
only, align the mounting tabs with this horizontal
line, not touching the cabinet bottom as described
in Step D.
REAR WALL TEMPLATE
Centerline
Draw a Vertical Line
notches
of Top Cabinet
Hole A
Draw a horizontal line on
wall at the bottom of "Rear
Wall Template".
NOTE: Holes A and B are inside area E. If neither of
Holes A and B are not in a stud, find a stud somewhere
in area E and draw a circle to line up with the stud. It is
important to have at least one wood screw mounted
firmly in a stud to support the weight of the
microwave. Set the mounting plate aside.
8
Publicidad
