Titan AirCoat 0508074A Manual Del Propietário página 9

clearing the Suction Tube (optional)
1. Turn the pressure control knob
counterclockwise to the minimum
setting.
2. Turn the PRIME/SPRAY valve to
PRIME.
3. Move the pump ON/OFF switch to
the OFF position.
4. Move the compressor ON/OFF
switch to the OFF position.
5. Wait a couple seconds, then
trigger the gun into the material
container to release built up
fluid pressure from the pump and air pressure from the
compressor.
6. Lock the gun by flipping the trigger lock into lock position
(see spray gun manual).
7. Remove the suction hose from the material and hold it
above a bucket of water or solvent. Leave the return hose
in the material bucket.
IMPORTaNT: Do not use mineral spirits or paint thinner on
latex paint, the mixture will turn into a jelly-like substance
that is difficult to remove.
8. Move the pump ON/OFF switch to the ON position.
9. Turn the pressure control knob to 1/2 maximum pressure.
This will draw the remaining material in the suction hose
through the pump, down the return hose and into the
material bucket.
10. Turn the pressure control knob counterclockwise to the
minimum setting.
11. Remove the spray tip and guard and place them into a
container of the appropriate solvent.
12. Place the attached suction hose and return hose into the
container of water or appropriate solvent.
13. Increase the pressure to 1/2 the maximum pressure. Let
the water or solvent circulate for 2-3 minutes to flush paint
out of the pump, the suction hose and the return hose.
clearing the Paint hose
1. Turn the pressure control knob counterclockwise to the
minimum pressure setting.
2. Turn the PRIME/SPRAY valve to
SPRAY.
3. Unlock the spray gun trigger.
4. Carefully trigger the gun with the
spray tip removed against the
inside of the material container.
5. Turn the pressure control knob
slowly clockwise until material
starts to flow into the container. As
soon as the water or solvent starts
to emerge from the spray gun,
release the trigger.
6. Change to clean water or solvent and continue circulating
for another 5 minutes to thoroughly clean the hose, pump
and spray gun.
7. Turn the pressure control knob counterclockwise to its
lowest setting.
8. Turn the PRIME/SPRAY valve to PRIME.
9. Trigger the gun into the water or solvent container to
release built up fluid pressure from the pump.
10. Lock the gun by flipping the trigger lock into lock position
(see spray gun manual).
11. Move the pump ON/OFF switch to the OFF position.
© Titan Tool. All rights reserved.
Final cleanup
1. Remove the hopper assembly or optional suction set from
Pump ON/OFF
Switch
2. Clean the threads of the inlet valve with a damp cloth.
3. Fill the inlet valve with water or with a
4. Make sure that the PRIME/SPRAY
Compressor
ON/OFF Switch
5. Turn on the pump by moving the pump
6. Increase the pressure by turning the
7. Turn the PRIME/SPRAY valve to SPRAY to distribute the oil.
NOTE: Proper cleaning and oiling of the pump after use
8. Turn the pressure control knob counterclockwise to its
9. Turn the PRIME/SPRAY valve to PRIME.
10. Unlock and trigger the gun to remove any pressure that
11. Lock the gun by flipping the trigger lock into lock position
12. Turn off the pump by moving the pump ON/OFF switch to
13. Remove the material hose and air hose from the spray
14. Wipe the entire unit, hose, and gun with a damp cloth to
PRIME/SPRAY
Valve
Pressure
Control Knob
9
the inlet valve.
light household oil.
valve is set to PRIME and that the
pressure control knob is turned
counterclockwise to its lowest
pressure setting.
ON/OFF switch to the ON position.
pressure control knob clockwise 1/2
turn.
are the most important steps to perform to insure
proper operation after storage.
lowest setting.
may still be in the hose.
(see spray gun manual).
the OFF position.
gun using two adjustable wrenches. Refer to the spray
gun Owner's Manual for gun cleaning instructions.
remove accumulated paint.
English
PRIME/SPRAY
Valve