Operating The Rsp-1580; Front Panel Overview; Remote Control Overview; Overview Of Buttons And Controls - Rotel RSP-1580 Manual De Instrucciones

English

Operating the RSP-1580

Considering its large number of features, settings and options, this Rotel
RSP-1580 is remarkably easy to operate. The key to operating the unit
is its system of On-Screen Displays (OSD) which guide you through
various choices.
The processor can be operated from the front panel or the remote control.
Front panel controls are unusually simple to use, with just a few knobs
and buttons to guide you through OSD menu options. The remote control
provides more complete control options.
To guide you through the operation of the unit, this section of the manual
starts with explaning the basic layout and function of the front panel and
the remote control. Then, we explain the basic operations such as turning
the unit on and off, adjust volume, selecting a source for listening, etc.
Following that is a detailed explanation of surround sound modes and
how to configure the unit for various types of recordings. Finally, there
are instructions for additional features and zone (MON) operation. All
of these are features that may be used in normal operation. The last
section of the manual (Configuration) details options that may be selected
during initial setup and configuration of the unit, many of which will be
set once and left untouched.
Throughout this manual, numbers in square boxes refer to the main unit
illustration at the front of this manual. Letters refer to the remote handset
illustration. When both appear, the function is found on both the unit's
front panel and on the remote. When only one appears, that function is
found either only on the main unit, or only on the remote.

Front Panel Overview

The following is a brief overview of the controls and features on the front
panel of the unit. Details concerning the use of these controls are provided
in subsequent sections of this manual describing various tasks.
Front Panel Display
2
The large TFT display on the front panel displays the OSD menu of the
RSP-1580. The setup of this unit can be done directly through this front
panel display. In addition, it can also display any 2D video source up
to 1080p.
Remote Sensor
This sensor receives IR signals from the remote control. Do not block
this sensor.
Note: The remainder of the buttons and controls on the front panel are
described in the Overview of Buttons and Controls section.

Remote Control Overview

The RSP-1580 is supplied with an easy to use remote control RR-CX93.
The unit can be set to IR code 1 or IR code 2 in case the unit is conflicting
with other Rotel remote codes. Push IR/AUD key and 1(2) at the same
time sets the remote control into IR code 1(2). Point the remote to the
RSP-1580 and press 1(2) for 5 seconds sets the RSP-1580 in IR code
1(2) . The factory default is IR code 1.
You can also set the CD codes for PLAY, STOP, FAST FORWARD, REV etc,
from the factory default IR code 1 to 2, if you find the unit is interfering
with other Rotel CD players in your system.
To change the CD code, point the remote at the unit and press "CD" and
2 (1) keys at the same time. Release the "CD" key and continue to press
the 2 (1) key for more than 5 seconds until the unit changes the code.

Overview of Buttons and Controls

This section provides a basic overview of the buttons and controls on the
front panel and the remote control. Detailed instructions on the use of
these buttons are provided in the more complete operating instructions
in the following sections.
STANDBY and Power ON/OFF Buttons
1
The front-panel STANDBY button and the remote control ON/OFF button
activate or deactivate the unit. The rear panel master POWER switch must
be in the ON position for the remote standby function to operate.
VOLUME Knob and VOLUME +/- Buttons
The VOLUME +/- buttons on the remote and the large rotary control on
the front panel provide the master VOLUME control, adjusting the output
level of all channels simultaneously.

DISPLAY Button

7 C
Push this button to show the current Audio and Video source, input mode
and output mode. If the OSD on the front panel is turned OFF, press this
key for more than 5 seconds to activate the OSD on the front display.
MENU Button
7 D
Navigating and Select keys (FUNCTION)
The MENU button pulls out the OSD on the TV or front panel. Use the
navigation keys UP/DOWN/LEFT/RIGHT and ENT (SEL) to access the
various menus.

MUTE Button

7B
Push the MUTE button once to turn the sound off. An indication appears
in the front panel and on-screen displays. Press the button again to restore
previous volume levels.

INPUT Buttons

5 K
This button on the front panel can be used to change sources.

MON button

5 K
The MON button can be used to display the sources sent to MON 2,3,4
HDMI outputs. Use the LEFT/RIGHT navigation keys to change the sources
to send to MON 2,3 or 4.
MODE button SUR+
5
E
The MODE/SUR+ button serve to display surround mode information
of current listing/viewing media, which can be set when selecting input
source. Use the LEFT/RIGHT navigation keys to change the mode.
J
Other 3 buttons on the remote allow direct selection of certain surround
modes for current playing media.
2CH: change the audio mode to STEREO, DOWN MIX or BYPASS.
PL C: change the audio mode to Pro Logic Cinema.
PL M: change the audio mode to Pro Logic Music.
23
A
8 B