GBC MFPP-C1 Manual De Instrucciones De Operación página 13

MFPP-C1 Punch Die Sets
The MFPP-C1 uses a variety of easily interchangeable die sets that allow you to punch documents in line for several different binding styles. By selecting
the appropriate die set, you can use your MFPP-C1 to punch documents in any of the following binding styles. DuraGlide HD™ die sets are shown in bold
where available.
Die Set Description
For Plastic Comb Binding:
1
PB Plastic Bind; Hole Size: 8mm x 2.9mm (0.313" x 0.116") (LxW); Center-to-Center Hole Spacing: 14.3mm (0.563")
* When the Plastic Comb binding die is used in the 21 hole configuration on A4 width paper (297mm), there is the potential for the outer edge of holes 1 and 21 to be torn. The theoretical
paper edge should be 1.62mm from the edge of the sheet. This event is dependent on paper type, paper width and hole alignment optimization. To avoid this issue, it is recommended
to use a 20 hole configuration instead. 20 hole comb binding supplies are commonly available from GBC and other manufacturers and are considered more optimal than the 21 hole
configuration.
For Twin Loop™ Binding:
1
W3 Wire; Square; 3 Holes per inch; Hole Size: 4mm x 4mm (0.156" x 0.156") (L x W); Center-to-Center Hole Spacing:
8.5mm (0.333")
1
W2 Wire; Rectangle; 2 Holes per inch; Hole Size: 6.4mm x 5.4mm (0.250" x 0.214") (L xW); Center-to-Center Hole Spacing:
12.7mm (0.500")
1
eWire; Square; 3 Holes per inch; Hole Size: 5mm x 5mm (0.197" x 0.197") (L x W); Center-to-Center Hole Spacing:
8.5mm (0.333")
1
W3 Wire; Round; 3 Holes per inch; Hole Size: 4mm (0.158") Diameter; Center-to-Center Hole Spacing: 8.5mm (0.335")
1
W2 Wire; Round; 2 Holes per inch; Hole Size: 6.5mm (0.0.256") Diameter; Center-to-Center Hole Spacing: 12.7mm (0.5")
1
eWire; Round; 3 Holes per inch; Hole Size: 5.5mm (0.217") Diameter; Center-to-Center Hole Spacing: 8.5mm (0.333")
For Color Coil™ Binding:
1
C4 Coil; Round; 4 Holes per inch; Hole Size: 4.4mm (0.174") Diameter; Center-to-Center Hole Spacing: 6.3mm (0.2475")
1
C4 Coil; Oval; 4 Holes per inch; Hole Size: 4mm x 5mm (0.158" x 0.197") (L x W); Center-to-Center Hole Spacing:
6.3mm (0.2475")
For Velo Bind:
®
1
VB Velobind ; Round; 1 Hole per inch Hole Size: 3.2mm (0.125") Diameter; Center-to-Center Hole Spacing: 25.4mm (1")
®
1
VB Velobind ; Round; 1 Hole per inch Hole Size: 3.2mm (0.126") Diameter; Center-to-Center Hole Spacing: 25.4mm (1")
®
For Loose Leaf Binding:
1
3 Ring Binder; U.S. (Standard Loose-leaf Patterns); Hole Size: 8mm (0.316") Diameter
1
3 Ring, 5 Ring, 7 Ring; U.S. (Standard Loose-leaf Patterns); Hole Size: 8mm (0.316") Diameter
1
4 Ring Binder; European (Standard Loose-leaf Patterns); Hole Size: 8mm (0.315") Diameter
1
4 Ring Binder; European (Standard Loose-leaf Patterns); Hole Size: 6.5mm (0.256") Diameter
4 Ring Binder; Scandinavian (Standard Loose-leaf Patterns); Hole Size: 6.5mm (0.256") Diameter
©2020 GBC, Lake Zurich, Illinois - All rights reserved.
19-LTR 21-A4
32-LTR 34-A4
21-LTR 23-A4
34
32-LTR 34-A4
21-LTR 23-A4
34
44-LTR 47-A4
44-LTR 47-A4
11
12
3
7
4
4
Graphics do not represent actual punch pattern dimensions or spacing.
MFPP-C1
GBC Part Number
Die, Comb Bind*
Die, Comb Bind, HD*
Die, Wire 3.1, Sq.
Die, Wire 2.1, Sq.
Die, eWire, 3:1, Sq.
Die, Wire, 3:1, Rnd.
Die, Wire, 2:1, Rnd.
Die, eWire, 3:1, Rnd.
Die, Coil, Rnd.
Die, Coil, Rnd, HD
Die, Coil, Oval
Die, Velobind , 11 Holes, Ltr.
®
Die, Velobind , 12 Holes, A4.
®
Die, 3 Hole, 8mm
Die, 3 Hole, 8mm, HD
Die, 3/5/7 Hole, 8mm
Die, 4 Hole, 8mm
Die, 4 Hole, 6.5mm
Die, 4 Hole, Scan
GB
7714023 / 7714024
7714035
7714027 / 7714028
7714025 / 7714026
7714031
7714015
7714014
7714030
7714012 /7714013
7714033
7713916
7714021
7714022
7714016
7714034
7714017
7714018
7714019
7714020
13