Quick Start-Up Instructions - HotSpring LIMELIGHT Serie Manual Del Propietário

PRECISION JETS
Precision jets are small, producing a precisely narrow stream of
massaging action. They are placed in groups to perform a soft, soothing
massage.
DIRECTIONAL AND ROTARY JETS
These jets deliver a great massage to the feet, back and shoulder areas.
These jets may provide either a direct stream, or two different types
of rotating massage patterns. Also, the speed of the rotation can be
changed by rotating the jet faceplate from a full stream, to shutting
the jet completely off. To avoid damage to your spa's plumbing and
components, do not turn off more than half of these jets at the same
time.
WATER FEATURE
The PRISM, PULSE , FLAIR , and FLASH spas come equipped with
a Vidro ® water feature. This water feature can be turned on or off when
the two-speed pump is on low speed (tranquil mode) or high speed. To
function correctly, the water feature on/off lever must be placed in the full
on position only.
If the lever is not in the full on position when the pump is on high speed,
it is likely that the water feature will project water substantially farther out
into the spa as the on/off lever is opened. This is not proper operation.
If this occurs, the pump should be turned off, the water feature lever
rotated to the full on position and the pump turned on again.
When not in use turn the on/off lever to the OFF position.
CAUTION: Partial blockage of water flow at entrance of water feature
will cause the water to flow farther into or over the spa.
HOT SPRING LOGO LIGHT
The HOT SPRING logo on the front of the spa illuminates several
colors. These colors indicate the power, water temp ready and status of
the spa without having to open the cover to look at the control panel.
Status indicator - all spa Ready indicator - water is ready, within
functions are working 2°F of set temperature when green
properly when green
See Logo Light Trouble
shooting guide for more
color information
Power indicator - Power to spa is on when blue
Ready Indicator: The GREEN indicator will light when the spa water
temperature is within 2°F (1°C) of the set temperature, and will turn
off when the temperature is outside of that range. If you increase or
decrease the temperature setting of the spa, the ready indicator will
turn off until the water temperature reaches the acceptable range for
the new temperature setting. A flashing RED indicator means a problem
may exists with the temperature sensor (see Logo Light Troubleshooting
section for more information).
Power Indicator: The BLUE indicator is 'on' when the spa is properly
supplied with power. It also provides a diagnostic function–a flashing
RED indicator indicates that the heater high limit has tripped, meaning
that either the spa water is above its acceptable temperature range, or
a malfunction has occurred within the spa (such as low circulation due
to clogged filters). An 'off' BLUE indicator means that there is a problem
with the spa control box or the power supplied to the spa (see Logo Light
Troubleshooting section for more information).
Getting Started
English Spanish
Status Indicator: A GREEN indicator is on when spa functions are
working normally. A YELLOW indicator is on when a spa function
requires attention. A RED indicator is on and flashing when there is an
issue with the spa functions and needs immediate attention (see Logo
Light Troubleshooting section for more information).

QUICK START-UP INSTRUCTIONS

BEFORE YOU FILL YOUR SPA
Make sure your spa has been properly installed per all local codes, this
includes the location of the spa, the foundation of the spa as well as the
electrical installation of the spa. Installation instructions in the form of a
Pre-Delivery Instruction booklet can be obtained from either your HOT
SPRING dealer or online at:
www.HotSpring.com/planning-tools/pre-delivery-instructions
DO:
• Know which water treatment system you will be using and make sure
you have necessary chemicals available. Read all of the instructions
that come with the system.
• Have FRESHWATER 5-way Test Strips Available.
• Have FRESHWATER Salt Test Strips Available if using the Salt system.
• Have pH/Alkalinity Up & Down available.
• Know the "Hardness" of your water, contact your dealer to help you with
this information. See Water Quality and Maintenance for more information.
IMPORTANT: The spa can be filled with "softened" water as long as
the calcium hardness parameters (pg. 2) are maintained.
• Purchase the Clean Screen
contaminants from the tap water. This is recommended, not required.
DON'T:
• Power up the spa until it has been filled with water! Power to the
spa automatically activates critical components within the spa, such
as controls, heater, circulation pump, and other systems. If power
is supplied to these components prior to the spa being filled, the
components will be damaged, and this may result in a non-warranty
component failure.
• Fill the spa with hot water or cold water with cold water temperature
below 50º F (10º C)! Tripping of the high-limit thermostat may result
causing your spa to stop functioning.
• Use your spa after filling until all of the steps listed below START-UP
are completed!
• Add chlorine if treating your spa with polyhexamethylene biguanide
(Biguanide, PHMB, eg. BaquaSpa
Page 5
French
pre-filter to remove unwanted
®
® ) sanitizer.