Publicidad
Idiomas disponibles
Idiomas disponibles
English
tem only.
•
To actuate the tool, depress the safety against the wor-
kpiece, and then pull the trigger.
•
To actuate the tool again, you will need to release the sa-
fety fully and release the trigger before you repeat above
procedure.
•
Make sure you are driving against workpiece before you
pull the trigger.
Jam clearing for concrete tool
•
In the case of fastener jam, disconnect the battery before
you perform any actions.
•
Pressing the magazine release lever located on the tool's
body as no. 1.
•
Remove the magazine and safety A as no. 2 & 3.
•
Remove the hammed fastener with needle-nose pilers or
similar type of tool. Do no use your hand to remove the
fastener.
•
Assemble back the Safety A and Magazine after you clear
•
the jam fastener.
Charge the battery and LED showed on tool and battery
charger
•
There is battery come along with the tool. It will take 2
hours before the new battery can be fully charged.
•
There will be red LED lightening when the battery charger
is connected to electric power and no battery is on the
battery charger.
•
The LED indicator on the battery charger will turn red
when it is charging a battery.
•
The other LED indicator will turn green when the battery
is fully charged.
•
In the case of abnormal battery temperature, the red LED
will blink in sequence.
•
In the case of abnormal battery, the red LED light up and
replaces the new now.
•
When the tool is connected to a charged battery, the LED
indicator on the tool will turn green.
State of Battery Charger LED Indicator
State
Red LED
Green LED
1
OFF
Idle – Input Power Available
ON
Battery Installed and
OFF
2
ON
Charging
3
Battery at Full Charge
OFF
ON
4
Over Temperature Protection
Blinking (ON 0.5s/OFF 0.5s)
Blinking (ON 0.5s/OFF 0.5s)
5
Over Charge Time
Blinking (ON 0.5s/OFF 0.5s)
Blinking (ON 0.5s/OFF 0.5s)
24
FOX cataleg.indd 24-25
FOX cataleg.indd 24-25
Maintenance instruction
General maintenance
•
The employer and tool operator are responsible for as-
suring that the tool is kept in safe working order. Further-
more, only service personnel trained by the manufacturer,
distributor, or employer shall repair the tool and shall use
the parts or accessories that are supplied or recommen-
ded by the tool manufacturer/distributor.
•
CAUTION disconnect the battery before performing any
maintenance.Always keep the tool in clean condition.
Wipe off grease or oil with dry clean cloth to prevent
accidental tool drop. Avoid using solvent base cleaner to
clean the tool, certain solvent will damage or weaken the
composite parts of the tool. Clean the intake filter regu-
larly to keep the tool in full efficiency.
•
NEVER use a tool if there is any doubt.
•
WASTE DISPSAL Follow national regulations for waste
disposal so as not to impose hazards to personnel and
the environment
Lubrication and cleaning
•
This tool should not need extra lubrication since the fuel
already contains some lubrication oils.
•
The combustion chamber and cylinder can be cleaned by
applying automobile carburettor cleaner. You will need to
remove the 2 screws on the handle and 4 screws on the
top cap to expose the internal component of cylinder.
Cold weather
•
This tool is not suggested to be used in cold weather. The
cold weather will decrease the combustion efficiency and
the battery performance. Use the tool only at temperature
above -7°C(19°F).
Storage
•
When not in use for an extended period, apply a thin coat
of the lubricant to the steel parts to avoid rust. Do not
store the nailer in a cold weather environment. When
not in use, the nailer should be stored in a warm and dry
place. Keep out of reach from children.
The display shows the status of the battery on
the tool
Status
Meaning
All LEDs show green
Battery power more than 80%
Two LEDs show green
Battery power more than 80% to 60%
One LED shows green
Battery power more than 60% to 40%
One LED blinks green
Battery power more than 40% to 20%
One LED shows red
Battery power below 20%
Trouble shooting
Symptom
Counter measures
Red LED indicator light is on
•
Battery power might be too low.
and the tool does not operate.
•
Replace battery with a fully charged
one.
Tool operates normally but
•
Adjust the depth of drive setting to
does not drive the fasteners
deepest.
to flush.
•
Clean the cylinder with proper
cleaner.
•
Check battery and replace as
required.
•
Depress the safety and hold for 1
minute before activating the trigger.
If the tool does not fire, there might
be seal leaking over the combustion
chamber. Send to service center
near you.
Fan does not run, and the LED
•
The battery is dead. Replace the
indicator light is red.
battery with a fully charged one.
•
If all above-mentioned conditions
do not work, send to service center
near you.
Battery is unable to charge, or
•
Replace the battery. If this action
the battery charger is getting
solves the problem, the battery is
hotter when charging.
damaged or exhausted.
•
Replace the battery charger if the
battery is functioning normally on
tool but cannot be charged by the
battery charger.
Battery charger is getting
•
The battery charger is damaged and
hotter, produces noise or start
should not be used any more. Unplug
to smoke.
the battery charger immediately and
replace it with a new battery charger.
Work contact element (safety)
•
The work contact element is bending,
is not fully depressed and the
or some dirt is stuck in the track of
tool cannot be used.
the safety mechanism. Clean the sa-
fety track. Repair or replace the work
contact element by service center
representative.
•
Lock out mechanism is active. Load
more fasteners.
Tool does not operate, but the
•
Run out of fuel, replace a new fuel
Green LED indicator light is on
cell.
and the fan can work.
•
Spark wire is loose, check the spark
wire by removing the cap.
•
Spark plug is dirty. Clean the spark
plug.
•
If all above-mentioned conditions
do not work, send to service center
near you.
Tool operate normally, but no
•
Wrong type of fasteners is used.
fastener is driven.
Please change to correct fasteners.
•
The cylinder needs cleaning.
•
Fastener is jammed, clean the jam-
med fastener before use.
•
The fastener pusher did not engage
properly with the fastener strip.
Adjust to fully engagement.
Combustion chamber is not
•
The work contact element (safety)
returning to start position.
is bending or dirty. Check the work
contact element and repair or replace
it. Clean the safety track.
Driver did not return to initial
•
Check and replace full battery.
position, miss fire frequency
•
Clean the tool with proper cleaning
get higher than usual.
fluid.
•
Check for piston ring wear status.
•
The tool maybe over heated. Clean or
replace the
•
intake air filter.
English
Tool appears to be losing
•
Check fuel cell.
power.
•
Clean or replace air intake filter.
•
Check spark plug wire.
•
Clean the tool with proper cleaning
fluid.
For failure other than above situation, please stop using the tool and contact
your local dealer for service.
Please send the tool back to the tool manufacturer/distributor if failure other
than those as tabulated above occurs.
10/07/2020 13:40:34
10/07/2020 13:40:34
25
Publicidad
