Publicidad
Idiomas disponibles
Idiomas disponibles
Cleaning
WARNING:
all air vents with clean, dry air at least once a week.
To minimize the risk of eye injury, always wear ANSI
Z87.1 approved eye protection when performing
this procedure.
WARNING:
harsh chemicals for cleaning the non‑metallic parts
of the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid get
inside the tool; never immerse any part of the tool into
a liquid.
Cleaning and Emptying the Vacuum
WARNING:
never use the vac without its filter.
iMPORTAnT: Maximum dust collection will only be
obtained with clean filters and an empty dust canister.
If dust begins to fall back out of the product after it is
switched off, this indicates that the dust canister is full and
requires emptying.
nOTE: The filter is re-usable do not throw it away when the
product is emptied. We recommend that you replace the
filters
28
,
29
every 6–9 months depending on frequency
of use.
To Empty the Dust Canister and Remove
the Pre-filter (Fig. M–P)
1. Lift and remove the lift away dust canister
chassis
24
as shown in Fig. M.
2. While over top of a trash can, grip the recessed tabs
the pre-filter
26
and pull upwards to remove the pre-filter
with cyclones and dust canister cap
3. Empty the contents of the dust canister
4. Tap the pre-filter
26
as necessary to remove any debris.
Inserting Pre-filter (Fig. O)
nOTE: The filter housing fits snuggly in the dust canister and
may be difficult to remove at first.
1. Install the pre-filter
26
ensuring the dust canister tab
recessed tabs
25
as shown in Fig. O.
2. Install the dust canister onto the chassis
firmly into position.
Removing filters (Fig. M—P)
1. Lift and remove the lift away dust canister
chassis
24
as shown in Fig. M.
2. Unscrew the dust canister cap
lift off the dust canister
3. Remove the foam filter
on the plastic loop
30
Blow dirt and dust out of
Never use solvents or other
Projectile/Respiratory Hazard:
10
from the
9
.
10
.
into the dust canister
10
31
aligns with the
24
, until it clicks
10
from the
9
counterclockwise and
10
.
28
and felt filter
29
by pulling
.
Cleaning the filters
1. Once the filters and pre-filter are removed from the dust
canister
10
the pre-filter
2. Rinse out the dust canister
3. Wash the foam filter
soapy water.
4. Ensure the foam filter
completely dry before refitting the filters into the dust
canister cap
5. Once the filters
place them inside the dust canister cap
felt side in the upwards position.
nOTE: The black foam side will be visible when looking
into the dust canister cap from the underside.
6. With the filters
cap
9
clockwise onto the pre-filter
7. The pre-filter
away dust canister
inserting Pre-Filter section.
iMPORTAnT:
•
‑
Wash the filters regularly using warm, soapy water
and ensure that it is completely dry before using
again. The cleaner the filter is, the better the product
will perform.
‑
It is very important that the filters are completely dry
and correctly in position before use.
Removing and Cleaning the Rotary
Brushes (Fig. Q)
WARNING:
from moving parts, disconnect the floor head and
extension tube from the vacuum before cleaning
25
of
or servicing.
1. To remove the rotary brush
slide the release latch
head
11
.
2. With the rotary brush
head
11
, grab and lift the rotary brush
out of the floor head
3. Wipe away any dust or debris on the rotary brush
4. Reinstall the rotary brush
aligning the keyed end of the rotary brush
gear located in the floor head
5. Align the squared end of the rotary brush
square slot on the floor head
6. Press firmly on the rotary brush
floor head
release latch
shake off or lightly brush any loose dust from
26
and foam filter
28
with warm soapy water.
10
28
and felt filter
28
and felt filter
9
.
28
,
29
are clean and completely dry,
28
,
29
fitted, screw the dust canister
26
can now be inserted into the lift
10
according to instructions in the
To reduce the risk of injury
32
from the floor head
33
towards the rear of the floor
32
released from the floor
11
to clean.
32
into the floor head
11
.
11
.
32
11
. Ensure you hear an audible click as the
33
snaps into its locked position.
English
and felt filter
29
.
29
with warm
29
are
9
with the white
26
.
11
32
completely
32
.
11
by
32
with the
32
with the
to secure it into the
11
Publicidad
