Publicidad
Idiomas disponibles
Idiomas disponibles
3. Install the cup charger into the charging station (Fig. D).
Ensure it is locked into place before proceeding.
nOTE: To remove the cup charger from the charging
base pull out on the retaining tabs
charger
19
out.
4. Plug the charger into an appropriate outlet before
inserting the battery pack.
5. Slide the battery pack
WARNING:
temperature over 40 ° F (4.5 ° C) and below 105 ° F
(+40.5 ° C).
6. Charger will not charge a faulty battery pack, which may
be indicated by the light staying OFF or the red light
rapidly blinking. Take charger and battery pack to an
authorized service center if light stays OFF or red light
rapidly blinks.
nOTE: Refer to label near charging light on charger for
blink patterns.
hot/Cold Pack Delay
When the charger detects a battery pack that is too hot
or too cold, it automatically starts a Hot/Cold Pack Delay,
suspending charging until the battery pack has reached an
appropriate temperature. The charger then automatically
switches to the pack charging mode. This feature ensures
maximum battery pack life.
A cold battery pack may charge at a slower rate than a warm
battery pack.
The hot/cold pack delay will be indicated by the red light
continuously flashing a short ON followed by a longer ON
(see charger for blink pattern). Once the battery pack has
reached an appropriate temperature, the charger will resume
the charging procedure.
Electronic Protection System
Li-Ion tools are designed with an Electronic Protection
System that will protect the battery pack against overloading,
overheating or deep discharge. The tool will automatically
turn off and the battery pack will need to be recharged.
Important Charging Notes
1. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
2. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local service center.
3. You may charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
21
and lift the cup
16
onto the charging station.
Only charge batteries in air
Charger Cleaning Instructions
WARNING:
charger from the AC outlet before cleaning. Dirt and
grease may be removed from the exterior of the charger
using a cloth or soft non‑metallic brush. Do not use
water or any cleaning solutions.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Wall mounted vacuum storage and battery
(Fig. D, E)
charging
The product can be attached to a wall to provide a
convenient storage and charging point for the appliance.
When mounting to a wall, make sure the mounting method
is suitable for the wall type and is appropriate to the weight
of the appliance.
1. Mark the location of the charging station screw holes on
the wall (at a height that allows the unit to hang without
hitting the floor and within reach of an electrical outlet
for charging the vacuum while it is on the charging
station
20
.
2. Fix the charging station
screws and plugs for the type of wall, and weight of the
appliance.
3. Install the cup charger
Ensure it is locked into place before p roceeding.
nOTE: To remove the cup charger from the charging
base pull out on the retaining tabs
charger out.
4. Plug the charger into an appropriate outlet.
5. With the battery
16
charge port
6
,located on the vacuum base, onto the
slots
23
of the charging station.
6. The white LED on the vaccum will flash indicating that
the battery is being charged.
7. The white LEDs will illuminate in segments, displaying
the state of chargein the battery
8. The completion of charge is indicated by the white LEDs
will turn off. The pack is fully charged and may be used at
this time or left on the charger.
ASSEMBLY AND ADJUSTMENTS
WARNING:
serious personal injury, turn unit off and remove
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Shock hazard. Disconnect the
20
to the wall using appropriate
19
into the charging station (Fig D.).
21
and lift the cup
installed on the vacuum slide the
To reduce the risk of
English
9
Publicidad
