Miche K1 EVO Manual De Uso Y Mantenimiento página 7

2
HUBS
� Warning
If you have any doubt whatsoever your service-repair abili-
ty, please take your bicycle to a qualified repair shop.
Before any maintenance operations on your wheels, always
wear gloves and protection glasses.
When replacing any broken sealed bearings please ensure sea-
led bearing correct measure and specification are used.
Rear hub
Right side 26x17x5 (6803)
Left side 26x17x5 (6803)
The K1 EVO hubs are easy to maintain. To do it, proceed as
follows:
FRONT HUB
The front hub does not require any particular maintenance.
For any extraordinary maintenance and replacement of bea-
rings, follow these simple steps:
• Extract the cage chamber (B) (Fig. 1)
Once the chamber successfully removed proceed replacing the
bearings.
• Apply light pressure to the axel (C) using a plastic-edged tool:
apply pressure until the bearing has been totally removed
from its housing including the axel (Pic. 2)
• Once the first bearing has been removed, using special 17mm
diameter extractor, you can then remove the second bearing
(Pic. 2)
Once these have been replaced, proceed in fitting the new
bearings:
• Fit the first bearing using a plastic-edged tool: apply pres-
sure until the soft pad is perfectly fitted within the housing
• Insert the axel (C)
• Centre the second bearing in line with the axel and fit it using
a push bearing that is big enough to contain the axel itself
(B).
• Insert the chamber on the axel (Pic. 3)
• Check that the wheel turns freely
� Warning
Use original spare parts exclusively provided by
Fac Michelin S.r.l. Any modification or alteration (also
graphic) of the product with non-original spare parts or
spare parts not delivered directly by Fac Michelin S.r.l., in-
volves the expiration of the guarantee.
REAR HUB
The rear hub requires cleaning and lubrication of the ratchets
in
the freewheel body.
For any maintenance:
• Insert allen wrentch 12mm (M) on right side of the hub (Pic. 4).
• Using allen wrentch 12mm (M), unscrew left stop (O)
Extract the axel of rear hub with the freehub body (E). if ne-
cessary
at this point you can:
• Change the bearings (S).
• Grease the cogs with low density grease (C).
• Extract from the axel the freehub body with the relative spa-
cer (Z) continue the cleaning process of hub. Warning: the
bearings of the freehub body and no replaceable.
Front hub
26x17x5 (6803)
26x17x5 (6803)
• Re-fit the axel inside hub body with the spacer (Z). Take care
to position of the pawls (Pic. 5)
• Insert allen wrentch 12mm (M) on right side of the hub (Pic. 6).
• Stopping left stop (O) with a allen wrentch 12mm (M) locking
at 15 Nm (Pic. 6)
• If necessary adjust the hub by working on the ring (H) (Pic. 6):
• Unlock the grub screw (I) with a allen wrentch (L) (Pic. 6).
• Turn the ring clockwise to drop the sliding, and in counter-
clockwise to rise the sliding.
• Lock the grub screw (I) (Pic. 6).
• Check the sliding of the wheel.
Please check that the hub is correctly tightened and closed,
failure to do so could lead to a serious or fatal accident.
� Warning
Use original spare parts exclusively provided by
Fac Michelin S.r.l. Any modification or alteration (also
graphic) of the product with non-original spare parts or
spare parts not delivered directly by Fac Michelin S.r.l., in-
volves the expiration of the guarantee.
3
SPOKES
The spokes used for the assembly of the wheels have the fol-
lowing sizes and characteristics.
K1 EVO Front wheel
disc
296 mm
CHANGE A SPOKE
� Warning
If you have any doubt whatsoever your service-repair abili-
ty, please take your bicycle to a qualified repair shop.
Before any maintenance operations on your wheels, always
wear gloves and protection glasses.
Use only spokes of the same length and characteristics of
those being replaced. Use original spare parts exclusively
provided by Fac Michelin S.r.l.
To replace a spoke on the K1 EVO is extremely easy in both
cases, front as well as rear wheels.
• Unscrew the nipples from the spoke with the corresponding
spanner.
• Once it has been unscrewed, slide off the spoke from its own
seat.
• Insert the new spoke.
• Screw nipple with washer.
Draw the spoke to be used for the replacement in the thread-
locker you chose to improve sealing.
To ensure the correct spoke tension please follow the indi-
cations below:
• Correct spoke tension for front wheel 1000 N
• Correct spoke tension for rear wheel, free wheel side 1300 N
To evaluate the correct wheel tension, please use a profes-
sional spoke tension gauge, we do not recommend that spoke
tension is estimated manually; please refer to a professional
Rear wheel
NO disc disc NO disc
296 mm 296 mm 295 mm
7