HK Audio LINEAR 5 MKII Serie Manual página 5

●
7
Data
This LED lights up orange when data is being transferred via the network
socket.
●
8
Preset
Use the Preset selection button to call up factory presets or a user preset
you can configure via the remote DSP CONTROL software. Tap the select
button once to scroll through Presets 1 through 4.
A separate manual explains how to program the four remote user presets.
You will find it on the LINEAR 5
MK II
Preset overview:
LINEAR 5
MK II
110 XA, 112 XA, 115 XA
1
Flat
2
Monitor
3
Low Cut
4
Remote (to access stored settings via the remote HK Audio DSP
CONTROL software)
The LINEAR 5 XA/FA models' factory presets:
MK II
Flat
Delivers linear response across the full frequency range
Monitor
Optimised to dampen the extra bass generated by floor cou-
pling when you set a speaker on its side for use as a monitor
Boost
Enhances low-frequency response when used as a stan-
dalone speaker without a subwoofer.
Low Cut A high-pass filter optimises the unit for use as a mid/high
unit paired with the LINEAR 5
The LINEAR 5 115 Sub A and 118 Sub A's factory presets
MK II
Front
Standard operating mode for a forward-facing subwoofer
Cardioid 1:1 For cardioid setups with two stacked subwoofers with one
vertical
forward-facing LINEAR 5
more on this)
Cardioid 1:1
For cardioid setups with two side-by-side subwoofers with
horizontal
one forward-facing LINEAR 5
4.2 for more on this)
Factory presets 1 to 3 address the speaker only and not the DSP Out.
Note: If you are operating the speaker in a network connected to
the remote DSP CONTROL software, you can configure the DSP Out
independently even when using factory presets 1 to 3. To learn more
about this, consult the separate DSP CONTROL manual. You will find it
on the LINEAR 5 download page at www.hkaudio.com.
MK II
The Remote Preset
Remote
This lets you call up a user preset that you previously stored
via DSP CONTROL for the speaker as well as for the DSP
Out. The speaker does not need to be connected to the
remote software to do this.
The remote preset's default setup is identical to factory preset 1 (Flat/
Front).
You can access the following DSP functions via the remote DSP CONTROL
software and save your settings in user presets:
Fully parametric 10-band EQ with variable filter characteristics for each fre-
quency band, high-pass and low-pass filters with variable filter characteris-
tics, Limiter, Delay, Polarity, Level, and Mute.
You can configure these parameters separately and independently for the
speaker and its DSP Out.
download page at www.hkaudio.com.
LINEAR 5 LINEAR 5
MK II MK II
112 FA, 115 FA 115 Sub A, 118 Sub A
Flat Front
Boost Cardioid 1:1 vertical
Low Cut Cardioid 1:1 hori-
zontal
115 Sub A or 118 Sub A
MKII
subwoofer. (see section 4.2 for
MKII
subwoofer (see section
MKII
LINEAR 7
118 Sub A
MADE IN GERMANY
Screenshot of the remote DSP CONTROL software. You can download this software free of charge from
the LINEAR 5 download page at www.hkaudio.com. The speaker and DSP Out parameters are identical,
but the double DSP power lets you configure each set independently.
●
9
Power
This rocker switch turns the power on and off. Set
it to Power to turn the electronic components on
and to Off to disconnect them from the mains
power supply.
Caution: Risk of electric shock! Do not open!
●
10
Power LED
Refer servicing to qualified service personnel.
Attention: Risque de choc élèctrique –
ne pas ouvrir!
As soon as the electronic components are supplied
with voltage, this LED lights up green.
●
11
Mains Input
The mains connection is designed as a lockable IEC 14 socket. In combina-
tion with the supplied lockable connection cable, the mains cable is locked
HK Audio is a brand of Stamer Musikanlagen GmbH
and secured against accidental slipping out.
Magdeburger Str. 8 • 66606 St. Wendel • Germany
Power
4
9
4
●
12
Auto Sleep
Use this recessed button to switch energy-saving Auto Sleep mode on and
off. Your speaker leaves the factory with the Auto Sleep button pressed to
enable this mode. This function puts the electronic components into Auto
Sleep mode when four and a half hours pass without the speaker register-
ing an audio signal, data sent to the network ports, or operation of a button
or knob on the electronics. The only way to wake it up is by switching the
Power button off and on again or patching an analogue audio signal into
the Input.
Heads Up: You cannot wake up the speaker via the network ports.
The only way to disable the Auto Sleep function is to press the recessed
switch (not pressed).
LINEAR 5
MK II
10
Power
Auto Sleep
Serial No.
On
12
Mains Input
100-240 V~ 50-60 Hz
1 A @ 1/8 output power
L
1
11
Input Thru
R
1
5
DSP Out
1.0
Off
2
12
Gain
0 dB
2
–6 dB
5