Basic Operations (Player, Source Select And Browse Sections) - Pioneer CDJ-350 Manual De Instrucciones

Ocultar thumbs Ver también para CDJ-350:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

1
Press [u] 1 to turn this unit's power off, then wait at
least 1 minute.
Never forcibly eject a disc directly after turning off the set's power.
Doing so is dangerous for the reasons described below.
The disc will still be spinning when ejected and could hit your
!
fingers, etc., causing injury.
Also, the disc clamp will rotate in an unstable way, and the disc
!
could get scratched.
2
Use the included disc force eject pin. (Do not use
anything else.)
The included disc force eject pin is mounted on the CDJ-350's bottom
panel. When the pin is inserted all the way into the insertion hole, the
disc is ejected 5 mm to 10 mm out of the disc insertion slot. Grasp the
disc with your fingers and pull it out.
Loading USB devices
Connect the USB device to the USB device insertion slot 3.
The [USB STOP] indicator lights.
Removing USB devices from the set
! Be sure to follow the procedure below when removing USB
devices from the set. Removing a USB device without following
this procedure could erase the set's management data and make it
impossible to read the USB device.
! When turning the set's power off, be sure to remove the USB device
first.
1
Press [USB STOP] 4 for at least 2 seconds.
The [USB STOP] indicator turns off.
2
Disconnect the USB device.
Basic Operations (player, source
select and browse sections)
3
TIME MODE
TIME MODE
i
AUTO CUE
AUTO CUE
k
DISPLAY
DISPLAY
4
USB
j
STOP
UTILITY
UTILITY
5
SOURCE SELECT
MP3/AAC
WAV/AIFF
TRACK SEARCH
IN/CUE
e
8
HOT LOOP
SEARCH
9
CUE
a
PLAY/PAUSE
REV
b
16
En
BACK
BACK
l
SELECT PUSH
SELECT PUSH
m
n
6
7
PLAYLIST
PLAYLIST
OUT
RELOOP/EXIT
BEAT LOOP
LOOP
OUT ADJUST
LOOP DIVIDE
+
f
g
h
MASTER TEMPO
c
d
FWD
About the power switch of this unit
 To turn the power on
Press [u] 1.
Turn on the power of this unit.
The [u] indicator lights green.
 To set to the standby mode
When this unit's power is on, press [u] 1 for at least 1
second.
This unit is set to the standby mode.
The [u] indicator lights red.
! When [u] is pressed again, the power turns on.
! This unit is equipped with an auto standby function. For details,
see About the auto standby function on page 22.
Playback
1
Load the source onto this unit.
2
Press [
This selects the source.
3
Turn the rotary selector m.
Select the track.
! To move to lower layers in a folder, select the folder then press the
rotary selector.
! To return to higher layers, press [BACK] l.
! Press [BACK] for more than 1 second to move to the top layer.
4
Press the rotary selector m.
The track is loaded and playback begins.
! When a disc containing music files recorded with a hierarchical
structure is loaded, playback starts from the tracks in the upper-
most level.
Pausing
During playback, press [PLAY/PAUSEf] b.
! Playback resumes when [PLAY/PAUSEf] is pressed again.
 Resuming playback from the position playing
just before the disc was ejected (Resume)
DISC
BPM
After ejecting the disc, immediately reload that same disc
LOCK
into this unit.
! The resume function only works when the same disc is ejected
VINYL MODE
then reloaded before loading another disc.
! The resume function does not work for USB devices.
TEMPO RANGE
Forward and reverse scanning
TEMPO
Press [SEARCH m, n] 9.
The disc is forwarded when [n] is pressed and held in.
The disc is reversed when [m] is pressed and held in.
0
Finding the beginnings of tracks (Track
Search)
Press [TRACK SEARCH o, p] 8.
Press the [p] to move to the beginning of the next track.
MULTI PLAYER
] 6 or [ ] 7 for at least 1 second.

Publicidad

Tabla de contenido
loading

Tabla de contenido