Publicidad
Idiomas disponibles
Idiomas disponibles
Do not use the saw without guard or when the guard is blocked.
c)
Floor close to the machine work place must be kept tidy and
d)
without loose materials and protrusions.
Provide appropriate work place illumination.
e)
Machine operator must be properly trained for use, operation and
f)
working with the machine.
Use only sharp cutting blades.
g)
Observe maximum speed indicated on the cutting blade.
h)
Make sure to use parts in accordance with the manufacturer's
i)
instructions.
Disconnect the saw from power supply when performing
j)
maintenance tasks.
If the power cord gets damaged during operation, disconnect the
k)
power supply immediately. DO NOT TOUCH POWER CORD BEFORE
DISCONNECTING FROM THE POWER SUPPLY.
If the saw is equipped with laser, replacement with laser of
l)
another type is forbidden and all repairs must be carried out by
the service. Do not aim the laser beam at people or animals.
Do not use the tool in stationary mode. It is not designed for use
m)
with sawing table.
Fix processed material to stable surface and secure with clamps or
n)
vice to eliminate shifting. This kind of work piece fixation is safer
than holding the work piece in hand.
Wait until blade comes to a complete stop before putting the
o)
power tool away. Cutting blade may jam and cause loss of control
over the power tool.
CAUTION! This device is designed to operate indoors.
The design is assumed to be safe, protection measures and
additional safety systems are used, nevertheless there is always a
small risk of injuries at work.
CONSTRUCTION AND USE
Circular saw is a hand-held power tool with insulation class II. It is
driven by a single-phase commutator motor. This type of power
tools is widely used for cutting wood and objects made of wood-
like materials that match with the tool size. Do not use the saw for
cutting firewood. Attempts to use the circular saw for purposes
other than specified will be considered an improper use. Use the
circular saw only with appropriate cutting blades with teeth with
sintered carbide tips. Circular saw is designed for light duty works in
service workshops and any individual, amateur activities (tinkering).
Use the power tool according to the manufacturer's instructions
only.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
Dust extraction outlet
1.
Upper guard
2.
Lower guard lever
3.
Parallel guide locking knob
4.
Saw base
5.
Cutting blade
6.
Collar washer
7.
Bolt for cutting blade fixing
8.
Lower guard
9.
Spindle lock button
10.
Front handle
11.
Cutting depth locking lever
12.
Switch
13.
Switch lock button
14.
Main handle
15.
Brush cover
16.
Knob for base bevel adjustment
17.
0° marker for bevel cutting
18.
0° marker for perpendicular cutting
19.
* Differences may appear between the product and drawing
MEANING OF SYMBOLS
CAUTION
WARNING
ASSEMBLY/SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
Parallel guide
- 1 pcs
1.
Cutting blade
- 2 pce
2.
Hexagonal key
- 1 pcs
3.
Transport case
- 1 pcs
4.
PREPARATION FOR OPERATION
CUTTING DEPTH ADJUSTMENT
Cutting depth can be set from the range of 0 to 65 mm.
• Loosen the cutting depth locking lever (12).
• Set desired cutting depth (use the scale).
• Lock the cutting depth locking lever (12) (fig. A).
INSTALLATION OF GUIDE FOR PARALLEL CUTTING
Use parallel guide when cutting material to narrow pieces. Guide
can be installed on left and right side of the power tool.
• Loosen the parallel guide locking knob (4).
• Insert parallel guide bar into two holes in the saw base (5).
• Set desired distance (use the scale).
• use the parallel guide locking knob to fix the parallel guide (4).
The parallel guide can also be used for cutting at angles ranging
from 0° to 45°.
Never put hand or fingers behind the working saw. When kick
back happens the saw can fall on the hand, it may be the cause
of heavy body injury.
MOVING THE LOWER GUARD
Lower guard (9) of cutting blade (6) is pushed away automatically as
the blade deepens into the material.
To remove it manually push the lower guard lever (3).
DUST EXTRACTION
Circular saw is equipped with dust outlet (1) that allows for
extraction of sawdust produced when cutting.
OPERATION / SETTINGS
SWITCHING ON / SWITCHING OFF
The mains voltage must match the voltage on the rating plate of
the circular saw. Hold the saw with both hands when starting up,
because engine turning moment may cause uncontrolled turn of
the power tool.
Remember that rotating parts of the saw rotate for some time
after the tool has been switched off.
The saw is equipped with the switch lock button (14) that protects
against accidental starting.
Switching on:
• Press the switch lock button (14) (fig. B).
• Press the switch button (13).
Switching off:
• Release pressure on the switch button (13).
CUTTING
• When starting operation always hold the saw firmly with both
hands by two handles.
12
Publicidad
