KUNERT MOLTO Manual De Instrucciones página 9

The carrycot is equipped with a cover which can be mounted by attaching the snaps of the cover to the
respective snaps on both sides of the hood (fig. 14).
MOUNTING AND REMOVAL OF THE PRAM SEAT
To mount the seat on the chassis, click it into designated slots (one on each side of the pram) (fig. 15) until
the hooks are locked (fig. 11). The hooks are locked automatically. The stroller seat may be mounted in
front-facing and rear-facing positions.
WARNING! Before you use the pram, make sure all blocking devices are activated.
To remove the seat, press the buttons on the both sides of the pram chassis (fig. 11).
WARNING This seat is not suitable for children under 6 months.
PRAM SEAT HOOD
The pram seat is equipped with a protective hood. To mount it, slide its hooks into designated slots on
both sides of the pram seat chassis until the hood is locked (fig. 16).
To remove the hood, press the buttons of the hooks on both sides and pull up the hood (fig. 16).The
position of the hood is adjustable. It can be positioned differently. To adjust the hood position, move it
forwards or backwards to achieve the desired result (fig. 17).If a new born baby is put in the stroller, it is
recommended to set the position of the seat which is to be used from the baby's birth in a position
similar to a lying one.
BACKREST ADJUSTMENT
The backrest can be adjusted in 4 positions. To lift the backrest up, you need to pull up the lever from
under the back of the seat and at the same time pull up the backrest up until you reach the desired
position. Next, release the lever (fig. 18).To recline the backrest, you need to pull up the metal lever, place
it in the desired position and release the lever.
SWIVEL FRONT WHEELS
The pram has front swivel wheels with a lock of the straight-ahead push. In order to lock the wheels, first
position them parallel to the rest of the pram and then turn the rim to the right (fig. 29). In order to
unlock the front wheels to go in all directions, simply turn the rim to the left.
FOLDING AND UNFOLDING THE PRAM CHASSIS
To unfold the pram chassis, lay it down flat, push the lock (fig. 1) and pull it up strongly while holding the
handle until the locking mechanism will lock into place (fig. 2).
WARNING! Always slightly lift the handle of the trolley while pressing the buttons
WARNING! Before using the pram, ensure the locking mechanisms are activated, if not, pull them tighter.
The chassis may be folded in two ways (with and without wheels):
- to fold the chassis with the wheels, first lock the front wheels by positioning them across the to the
pram. Then, press the lock button with your thumb (fig. 3) and then simultaneously pull the levers on
both sides of the handle (fig. 4).
- to fold the chassis without wheels, take off two front wheels (fig. 5) and rear wheels
(fig. 6). Then, press the lock button with your thumb (fig. 3) and simultaneously pull the levers on both
sides of the handle (fig. 4).
PARKING DEVICE
To activate the parking device, you need to step on the lever at the bottom of the pram (fig. 28). The
parking device will be released when the lever is lifted.
FOOTREST ADJUSTMENT
The footrest can be adjusted by simultaneously pressing side buttons while putting it in the desired
position (fig. 19).
MOUNTING AND REMOVAL OF REAR WHEELS
Before mounting the wheels, first mount the axes in the pram chassis. In order to mount the
axes, push the larger end of the axis into the absorber by pressing the red button, and then
release the button. Mount the axes on both sides of the pram and check whether fixed
properly (fig. 9).To mount the rear wheels, press the metal button in the central part of the
wheel (fig. 6) and then slide the wheel on the axis as far as it will go, release the button and
pull back the wheel until you hear a "click" sound.Always check whether the wheels are
mounted correctly. In case the pram wheel comes of when pulled, repeat the wheel mounting
procedure until mounted properly.
FASTENING THE HARNESS
9