Publicidad
Idiomas disponibles
Idiomas disponibles
1 - User instructions
EN
Installation
All the operations concerned with the installation (electrical and
gas connections, adaptation to type of gas, necessary adjustments,
etc.) must be carried out by qualified technicians, in terms with the
standards in force. For specific instructions, kindly read the part
reserved for the installation technician.
DO NOT FOCUS INENSEL ON THE LEDS AND DISPLAYS.
Use
Use Gas burners
The ignition of the gas burner is carried out by putting a small
flame to the upper part holes of the burner, pressing and rotating
the corresponding knob in an anti-clockwise manner, until the
maximum position has coincided with the marker. When the gas
burner has been turned on, adjust the flame according to need. The
minimum position is found at the end of the anti-clockwise rotation
direction.
For models with automatic/ simultaneous (with one hand) ignition, it
is sufficient to proceed as described above using the corresponding
knob. The electric spark between the ignition plug and the burner
provides the ignition of the burner itself. After ignition, immediately
release the push-button and adjust the flame according to need.
For models with a thermoelectric safety system, the burner is ignited
as in the various cases described above, keeping the knob fully
pressed on the maximum position for approximately 3/5 seconds.
After releasing the knob, make sure the burner is actually lit.
N.B.
• We recommend the use of pots and pans with a diameter
matching that of the burner, thus preventing the flame from
escaping from the bottom part and surrounding the pot;
• do not leave any empty pots or pans on the fire;
• do not use any tools for grill-cooking on Crystal hobs.
When cooking is finished, it is also a good norm to close the main
gas pipe tap and/or cylinder.
Models with Dual Wok burner (DWK)
Some models are equipped with a Dual Wok burner. It is possible
to light the central and external flame (F1+F2) by turning and
pressing the knob anti-clockwise or to light the central burner (F1)
only, as shown in the figure below.
F2
F1+F2 Max
F1+F2 Min
F2
2
Important
On floors with thermoelectric protection do not keep the ignite
button pushed for more than 15 seconds. If the burner has not
ignited after 15 seconds, open the door of the room and wait at
least one minute before making a further attempt.
Maintenance Gas/Electrical
Prior to any operation, disconnect the appliance from the electrical
system. For long-life to the equipment, a general cleaning operation
must take place periodically, bearing in mind the following:
• the glass, steel and/or enamelled parts must be cleaned with
• avoid leaving acid or alkaline substances on the working area
• the wall baffle and the small covers (mobile parts of the burner)
• the electrical parts are cleaned with a damp cloth and are lightly
• the stainless steel grids of the working area, after having been
N.B.- Cleaning of the taps must be carried out by qualified personnel,
who must be consulted in case of any functioning anomaly. Check
F1
periodically the state of conservation of the flexible gas feed pipe.
In case of leakage, call immediately the qualified technicians for its
replacement.
F1 Min
DO NOT USE STEAM CLEANERS
F1Max
F1
GAS
suitable non-abrasive or corrosive products (found on the
market). Avoid chlorine-base products (bleach, etc.);
(vinegar, salt, lemonjuice, etc.);
must be washed frequently with boiling water and detergent,
taking care to remove every possible encrustation. Dry carefully
and check that none of the burner holes is fully or partially
clogged;
greased with lubricating oil when still warm;
heated, take on a bluish tint which does not deteriorate the
quality. To bring colour back to its original state, use as lightly
abrasive product.
wok
Ø 20-32
*with reduction grid
Publicidad
