Publicidad
Idiomas disponibles
Idiomas disponibles
38
TROUBLESHOOTING
why aren't the function buttons working?
Make sure that the oven is not in Lockout mode. The lock
symbol
will show in the display if Lockout is activated.
To deactivate Lockout, press and hold the PROBE button
for three seconds. The unlock melody will sound and
UNLOCKING will appear in the display until the controls
are unlocked.
my oven is still dirty after running the
speedclean™ cycle. what else should i do?
The SpeedClean™ cycle only helps to loosen light soils
in your oven to assist in hand-cleaning of your oven.
It does not automatically remove all soils after the
cycle. Some scrubbing of your oven is required after
running the SpeedClean™ cycle.
i tried scrubbing my oven after running
speedclean™, but some soils still remain.
what can i do?
The SpeedClean™ feature works best when the soils
are fully soaked and submerged in water before
running the cycle and during hand-cleaning. If soils
are not sufficiently soaked in water, it can negatively
affect the cleaning performance. Repeat the SpeedClean™
process using sufficient water. Sugar-based and certain
greasy soils are especially hard to clean. If some
stubborn soils remain, use the Self Clean feature to
thoroughly clean your oven.
soils on my oven walls are not coming off.
how can i get my walls clean?
Soils on the side and rear walls of your oven may be
more difficult to fully soak with water. Try repeating the
SpeedClean™ process with more than the 1/5 cup (2 oz
or 60 ml) spray recommended.
will speedclean™ get all of the soils and
stains out completely?
It depends on the soil type. Sugar-based and certain
grease stains are especially hard to clean. Also, if stains are
not sufficiently soaked in water, this can negatively affect
cleaning performance. If stubborn or built-up stains
remain, use the Self Clean feature. Refer to the Self
Clean section of your owner's manual.
are there any tricks to getting some of the
stubborn soils out?
Scraping the soils with a plastic scraper before and during
hand-cleaning is recommended. Fully saturating soils
with water is also recommended.
However, certain types of soils are harder to clean than
others. For these stubborn soils, the Self Clean cycle is
recommended. Consult the Self Clean section of your
owner's manual for details.
is it safe for my convection fan, broil
burner or heater element to get wet during
speedclean™?
Yes. The convection fan, broiler burner or heater element
may get a little wet during cleaning. However, direct
spray onto the broil burner and heater elements is not
necessary because these are self-cleaning during regular
use.
Do i need to use all 1 cups (10 oz or 300
ml) of water for speedclean™?
Yes. It is highly recommended that 4/5 cup (8 oz or
240 ml) of water be sprayed or poured on the bottom
and an additional 1/5 cup (2 oz or 60 ml) of water be
sprayed on walls and other soiled areas to fully saturate
the soils for better cleaning performance.
i see "smoke" coming out of my oven's
vents during speedclean™.
is this normal?
This is normal. This is not smoke. It is actually water vapor
(steam) from the water in the oven cavity. As the oven
heats briefly during SpeedClean™, the water in the cavity
evaporates and escapes through the oven vents.
how often should i use speedclean™?
SpeedClean™ can be performed as often as you wish.
SpeedClean™ works best when your oven is LIGHTLY
soiled from such things as LIGHT grease splatter and
small drops of cheese. Please refer to the SpeedClean™
section in your owner's manual for more information.
what is required for speedclean™?
A spray bottle filled with 1 cups (10 oz or 300 ml) of water,
a plastic scraper, a nonscratch scrubbing pad and a towel.
You should not use abrasive scrubbers such as heavy-
duty scouring pads or steel wool. Except for a towel, all of
the materials you need are included in a special cleaning
kit with your new oven.
Publicidad
