cecotec bolero DRESSCODE 9500 INVERTER A Manual De Instrucciones página 33

ENGLISH
Please note
The levelling feet do not come fully fixed for easier installation, so be sure to fix all four before
levelling the washing machine.
1. When positioning the washing machine, you should check if the levelling feet are fully
fixed; if not, fix them. The lock nuts must be firmly locked to the bottom of the appliance
and the levelling feet securely locked into the lock nuts. Fig. 7
2. Once the washing machine is installed, press on the opposite corners of the top with both
hands in succession and shake the washing machine vertically downwards to check if the
levelling feet are firmly fixed and that the washing machine does not wobble. Fig. 8
3. If the washing machine wobbles, loosen the lock nut in the direction shown in Figure 9 with
the spanner provided until the machine is level and no longer wobbles. Fig. 9
4. Finally, use the spanner to fix the lock nut to the bottom of the washing machine (you can
also fix the levelling feet lightly by hand to prevent them from moving). Make sure the
levelling feet do not move. Fig. 10
Warning
1. The washing machine must be perfectly level and stabilised when all four feet are firmly
on the floor.
2. Incorrect levelling adjustment may cause loud noises, vibrations of the washing machine,
shifting of the washing machine, and other abnormal occurrences.
3. The air vent is located at the bottom of the washing machine (to avoid obstructions). Install
the washing machine on a solid, smooth, non-slip floor. Do not place the washing machine
on a soft blanket or wooden floor or on top of furniture, as this may cause unnecessary
injury.
4. OPERATION
Installing the washing machine
Connecting the inlet hose Fig. 11
1. Connect the inlet hose to the tap and fix it by turning it counterclockwise.
2. Connect the other end of the inlet hose to the inlet valve on the back of the washing
machine and secure it firmly clockwise.
Please note
- If the hose leaks after connection, repeat the process.
- Do not bend the hose.
- Check the inlet hose connection before every use.
64
Connecting the drain hose
- The drain hose should be placed at a height of 65-100 cm above the ground, otherwise it
may cause poor drainage. Fig. 12
- You can use the drain-hose bracket supplied to connect the drain hose to the wall, drain
pipe, or sink. Fig. 13
- Make sure that all hose connections are tight.
Please note
Do not immerse the end of the drain hose in water for the washing machine to work properly.
Electric connection
- Since the maximum current flow is 10 A when the interior temperature of the washing
machine increases, make sure that the power supply system (current, supply voltage, and
cord) in your home can meet the normal load requirements of electrical appliances.
- Connect the appliance to a properly installed and earthed outlet.
- Make sure that the household supply voltage matches the rated voltage of the washing
machine.
- Make sure the power plug matches the socket.
- Do not use multipurpose plugs, sockets, or extension cords.
- Do not connect or disconnect the plug with wet hands.
- When disconnecting the plug, hold it firmly and pull it out. Do not pull the power cord out
abruptly.
Warning
1. The washing machine must be properly earthed. If a short circuit occurs, earthing can
reduce the risk of electric shock.
2. The washing machine must be operated on a circuit separate from other electrical
appliances. Otherwise, the surge protector may trip, or the fuse may blow.
Washing machine operation
Please note
Make sure that the washing machine is properly installed before use.
Before first use, you should perform a complete washing cycle without laundry.
First use
1. Connect the power cord and inlet hose as described in the previous section.
2. Add some detergent (about 10 g) to the detergent drawer and close it.
3. Press the Power button.
4. Turn the selection knob to the Cotton position.
5. Press the Start/Pause button.
This will remove any water left in the washing machine from the manufacturer's test.
BOLERO DRESSCODE 9500 INVERTER A / BOLERO DRESSCODE 9500 INVERTER STEEL A
ENGLISH
65