Descargar Imprimir esta página

WERKU WK501400 Instrucciones Originales página 10

Equipo hidráulico airless a gasolina

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 12
ENG
ORIGINAL
"prime" mode (46)
knob to "prime/clean" setting (47)
unit (48)
The unit will start pumping and water
or flushing solvent as well as air bubbles will
be purged from system
from priming tube into waste bucket for 30 to 60
seconds then switch power to "off" (49)
suction tube from water or flushing solvent and
submerge in paint pail (50)
(51)
Paint should work itself from suction tube
to the unit to priming tube until paint discharges
from priming tube
Remove the priming tube from the waste bucket
and clip to suction tube and submerge in paint
pail (53)
Switch power to "on" (54)
airless gun into waste bucket and pull trigger (55)
Turn "spray/prime" switch to "spray" mode and
continue to spray into waste bucket (56)
painting.
PAINT.
Before painting, ensure the the unit has been
primed and verify that nozzle tip is aligned
properly
Remove or cover objects that you
want to protect from overspray and paint mist
Once primed, adjust nozzle to "spray" setting
(57)
Start spraying at the lowest setting on the
pressure control knob and increase pressure
as needed by turning clockwise to create a
good spray pattern (58)
techniques that follow on a scrap workpiece
before painting your workpiece.
PAINTING TECHNIQUES.
Before painting, ensure the the unit has been
primed and verify that nozzle tip is aligned
properly
Keep the airless gun approximately 30
cm from the surface
and move arm across at a steady rate while
staying 30 cm from the surface (59)
fan the airless gun or paint will be uneven (60)
Overlap strokes by half, always aim stroke at
bottom edge of last stroke (61).
CLEARING AIRLESS GUN TIP.
Occasionally, the airless gun tip will become
clogged with paint
clear airless gun tip
Adjust nozzle to "clean/eject" setting (63)
"spray/prime" switch to "spray" mode (64)
power to "on" (65)
Adjust pressure control
Turn "on" de
Let fluids discharge
Switch power to "on"
Switch power to "off" (52)
Point
Practice the painting
Keep airless gun straight
Do not
Follow these instructions to
Switch power to "off" (62)
Spray into waste bucket until
clog clears (66)
to "spray" mode (67).
CLEANING.
Turn power off and turn "prime/spray" switch to
"prime" mode to relieve pressure (68)
Remove
airless gun tip and remove (69, 70)
pressure and drain paint from tubes (71)
Place priming tube in empty waste bucket (72)
Submerge suction tube in water or flushing fluid
(73)
The unit will start pumping and water or flushing
solvent as well as air bubbles will be purged from
system
into waste bucket until fluid is clear (75)
fluid in priming tube is clear, switch power to "off"
(76)
Start
(77)
pail (79)
(80)
(81)
trigger, turn power "off" and relieve pressure (83,
84, 85)
(86)
the swivel connector (87)
Clean all parts in warm, soapy water or flushing
fluid with a bristled brush (89).
STORAGE.
When cleaning for long term storage (more
than 48 hours). it is important that the unit is not
stored with any water or water-based material left
in the pump, hose, tubes, or airless gun
will corrode the product
the the unit before storage
if not already removed (90)
mililitres of light household oil or a pump storage
product into each inlet (91)
switch to "spray" (92)
knob to "low pressure spray" (93)
over the paint hose outlet (94)
"on" for five seconds, then turn the power to "off"
(95)
will keep storage fluids in the unit (96)
the unit with a clean cloth
location out of reach of children.
MAINTENANCE.
Turn
The gasoline airless hydraulic equipment
Turn
has been designed for a long working life with
minimum maintenance
English
10
Release trigger
Plug in the unit and turn "on" power (74)
Let fluids discharge from priming tube
Turn "spray/prime" switch to "spray" mode
Switch power to "on" (78)
Change to waste bucket as paint thins
Turn "prime/ spray" switch to "prime" mode
Continue to flush until clear (82)
Remove the trigger guard from housing
Unscrew nut from housing, it is behind
Is very important clean
Turn pressure control
Turn "prime/spray" switch to "prime", this
Optimum use depends
Adjust nozzle
Unthread
Relieve
After
Paint into paint
Release
Remove filter (88)
This
Remove paint hose
Add about 30
Turn "prime/spray"
Hold a rag
Switch power to
Wipe the
Store in a clean dry

Publicidad

loading