Publicidad
Idiomas disponibles
Idiomas disponibles
No children or pregnant women should enter the work
u
area where the paint wire brushing is being done until all
clean up is completed.
A dust mask or respirator should be worn by all persons
u
entering the work area. The filter should be replaced daily
or whenever the wearer has difficulty breathing.
Note: Only those dust masks suitable for working with lead
paint dust and fumes should be used. Ordinary painting masks
do not offer this protection. See your local hardware dealer for
the proper respiratory protection.
NO EATING, DRINKING or SMOKING should be done
u
in the work area to prevent ingesting contaminated paint
particles. Workers should wash and clean up BEFORE
eating, drinking or smoking. Articles of food, drink, or
smoking should not be left in the work area where dust
would settle on them.
Environmental safety
Paint should be removed in such a manner as to minimize
u
the amount of dust generated.
Areas where paint removal is occurring should be sealed
u
with plastic sheeting of 4 mils thickness.
Wire brushing should be done in a manner to reduce
u
tracking of paint dust outside the work area.
Cleaning and disposal
All surfaces in the work area should be vacuumed
u
and thoroughly cleaned daily for the duration of the
wire brushing project. Vacuum filter bags should be
changed frequently.
Plastic drop cloths should be gatheredup and disposed
u
of along with any dust chips or other removal debris.
They should be placed in sealed refuse receptacles and
disposed of through regular trash pick-up procedures.
During clean up, children and pregnant women should be
kept away from the immediate work area.
All toys, washable furniture and utensils used by children
u
should be washed thoroughly before being used again.
Using cutting wheels
Do not use edge grinding/cutting wheels for surface grinding
applications because these wheels are not designed for side
pressures encountered with surface grinding. Wheel breakage
and injury may result.
Allow tool to reach full speed before touching tool to
u
work surface.
Apply minimum pressure to work surface, allowing tool to
u
operate at high speed. Cutting rate is greatest when the
tool operates at high speed.
Once a cut is begun and a notch is established in the
u
workpiece, do not change the angle of the cut. Changing
the angle will cause the wheel to bend and may cause
wheel breakage.
(Original instructions)
Remove the tool from work surface before turning tool off.
u
Allow the tool to stop rotating before setting it down.
Maintenance
Your STANLEY tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
u
switch off.
Unplug the charger before cleaning it. Your charger does
u
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your appliance/tool/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
u
from the interior (when fitted).
Protecting the environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with
normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according
to local provisions. Further information is available at
www.2helpU.com
Technical data
Voltage
V
DC
Rated speed (RPM)
min
-1
Disc diameter
mm
Disc bore
mm
Max disc thickness
grinding disc
mm
cutting disc
mm
ENGLISH
SCG400
AR
B2
BR
B3
18V (20V MAX)
9 000
115
22
6
3.5
35
Publicidad
