BURG-WACHTER Pure-Safe E FP Instrucciones De Uso página 5

Instruction Manual
Diagram
Keypad CLOSE
To lock the safe
Display
ENTER
Fingerprint sensor
Turn on the electronic lock and
with light ring
confirm the entry of a code
Emergency Lock
Foreword
Dear customer,
Thank you for purchasing this safe from the Pure-Safe series from
BURG-WÄCHTER. This safe is manufactured to a high standard
using the latest in technological advancements.
This Pure-Safe model can be operated with either a code or with
a fingerprint. In addition, all safes have an integrated mechanical
emergency lock.
Important: Please read the entire instructionmanual
before you start programming the safe.
We hope you enjoy using your new Pure-Safe,
Your BURG-WÄCHTER KG
Pure-Safe Elektronik E FP
Emergency lock operation
„Under no circumstances should you operate the electronics with an emer-
gency key inserted. It this has occurred, remove the emergency key and
press „"Close"" until the safe is properly locked.
Please note when replacing the battery:
If the door was opened using the emergency key, make sure that you
have removed the emergency key again before replacing the battery. The
electronics may only be operated if the emergency key has been properly
removed."
Important notes
• Be sure to store your user codes and the emergency key in a secure location
and not inside the safe (the emergency lock is located to the right of the
keypad)
• Don't use simple codes that are easy to guess (e.g. 1-2-3-4-5-6)
• For security reasons we recommend you do not use personal numbers such
as your date of birth or telephone number as a code to operate the safe
• If the safe is not going to be used for a prolonged period of time,
please remove the batteries
• The factory set admin code and default user code must be changed to your
own unique code to ensure the safe is secure
• The safe only achieves its intended protection after it is anchored in place
to a solid part of a building such as a wall or floor. Please use the pre-drilled
anchoring points (in the base and back wall of the safe) fixings to secure the
safe in place
• Please contact your retailer if you have any questions or technical issues
General
An admin code and user code are available to operate the safe, plus the
addition of up to 5 programmable fingerprints.
The admin code must have 8-digits.
The user code can be between 3 to 6-digits.
Admin code: 1-2-3-4-5-6-7-8 (factory set default)
User code: 1-6-8 (factory set default)
Technical specification
Blocking Times: After 3x wrong code entries: 5 minutes
After 10x incorrect fingerprint entries: 1 minute
Battery Specification: 4x AA MIGNON LR6 ALKALINE
Specified operating -15 °C to + 50 °C
conditions up to 95% rel. humidity
(non-condensing)
Signal tones + message in the display
1x beep Key entry registered. Start locking process, lo-
cking process successfully completed, during FP
learning procedure gently apply FP to sensor
2x beeps Input correct / accepted. Start opening process,
FP learning procedure successful, deletion of FPs
successful, user/admin code saved
3x beeps Input wrong / denied (CODE-ERROR, FP-ERROR)
1x long beep Fingerprints deleted successfully
8x beep + „BLOCK" Remove the emergency key if it is inserted in the
lock! If the emergency key is not inserted, please
remove any obstruction in the door so that it can
close properly!
8x beep + „ERROR" Replace the batteries and restart the process with
the door open. Contact the technical service if the
error message reappears
Light ring
The light ring is used to indicate the current state of the fingerprint
sensor and is located around the sensor:
Blue light The fingerprint sensor is ready for use/activated
Green light Successful fingerprint operation, fingerprint
successfully learned, stored fingerprints success-
fully deleted
Red light Incorrect fingerprint operation (not recognised or
incorrect fingerprint)
Installation
• Remove the enclosed emergency keys from the packaging.
• Use the emergency key to open the safe door (see diagram for location).
• Remove the plastic strip located by the battery compartment on the
inside of the door to activate the batteries.
• With the door still open, turn the emergency key and remove it from
the emergency lock hole. Only operate the electronics when you have
removed the key!
• Press the ENTER button.
• Enter the user code (factory default code: 1-6-8) and confirm by
pressing the ENTER button.
• The safe can now be programmed to your own admin and user code.
Deutsch I 5