BURG-WACHTER Pure-Safe E FP Instrucciones De Uso página 6

Chapter 1: Operation with a code
Opening the safe with the user code
• Press the ENTER button
• Enter the 3 to 6-digit user code (factory default code: 1-6-8) and confirm
with ENTER button. You will hear 2 short beeps.
The door will open automatically.
If you hear 3 short beeps, an incorrect code has been entered. Please try again.
Closing & locking the safe
Drücken und halten Sie die Tresortür zu. Die Tür verriegelt automatisch, wenn
Sie die CLOSE-Taste drücken. A short beep is heard at the end of the closing
process, the door is now successfully locked.
Achtung: In case of a blockage, you will hear 8 short beeps and the message
„"BLOCK" will appear in the display. The safe cannot be locked. If this message
appears and the emergency key is still in the lock, remove it! If the emergency
key is not inserted, please check for any obstruction and remove it so that the
door can close properly!
Then please repeat the process."
Programming the user code
The door must be open and the bolts must be retracted inside the door.
• Press the ENTER button.
• Enter a new user code (it must be between 3 to 6 digits max.) and
confirm with the ENTER button.
• You will hear 2 beeps and the message „GOOD" appears in the display,
indicating that the electronics have saved the new code.
• Press the CLOSE button.
The locking bolts will extend out. A new user code has been successfully
programmed.
Incorrect entries
If an incorrect code or fingerprint entry is made when the safe is locked/closed
the display will show "CODE-ERROR" or „FP-ERROR" and you will hear 3 short
beeps. A third successive incorrect code or fingerprint entry will result in the
electronic lock blocking any further entries for 5 minutes (Pincode). After 10
incorrect fingerprint attempts the electronics will block any further entries for 1
minute. After this blocking time, the safe can be opened with the admin code,
the correct user code or a valid fingerprint. If a wrong digit is entered during
code entry, it can be cleared by pressing the CLOSE button.
6 I Englsih
Opening the safe with the admin code
• Press the ENTER button.
• Enter the 8-digit admin code (factory default code: 1-2-3-4-5-6-7-8).
and confirm with ENTER button.
The display shows „PASS 1" and counts down for 10 seconds.
After this time, you will hear two short beeps and the door will open
automatically.
Caution: When the admin code is entered, the last programmed user code is
shown on the display briefly and then deleted. The user code must now be
re-programmed (see „Programming the user code").
The door can only be locked if a user code has been programmed.
Programming the admin code
The safe door must be open with the bolts extended out of the door.
• Press the ENTER button
• Enter the admin code (factory default code: 1-2-3-4-5-6-7-8) and confirm
with ENTER button
• The display shows „PASS 1" and counts down for 10 seconds. Within this
time, press the ENTER button again
• Now enter the new admin code (8 digits) and confirm by pressing ENTER
• „REPEAT" will appear on the display
• Enter the new admin code a second time and confirm with ENTER.
• The new admin code is saved when you see „GOOD" shown on the display
• You will also hear 2 short beeps to confirm
A new admin code has been successfully programmed.
Chapter 2: Operation with fingerprint
Opening the safe with a fingerprint
• For the fingerprint to be recognised it must be clean and dry.
• Press your finger on the sensor with gentle pressure. The fingerprint sensor
is automatically activated, it illuminates blue and is ready for use.
• Subsequently, the fingerprint sensor illuminates green and 2 short beeps
are heard if the fingerprint evaluation was successful
The door will open automatically.
If 3 short beeps are heard and the light ring illuminates red, the fingerprint was
not recognised. Please try again.
Programming mode: learning and deleting fingerprints
The door must be closed and the bolts must be extended.
• Press the ENTER button.
• Enter the admin code (factory setting 1-2-3-4-5-6-7-8)
and confirm with ENTER.
• The display shows „PASS 1" and counts down for 10 seconds. Within this
time, press the ENTER button again.
The following changes can now be made:
Add a new fingerprint
Note: For the fingerprint to be recorded it must be clean and dry.
• Enter the digits „23" on the keypad and confirm with the ENTER button
„STEP1" appears on the display. The fingerprint sensor illuminates blue and
is ready for use.
• Press the finger gently on the sensor and do not remove it until the light
ring goes out and you hear 1 beep.
• The display changes to „STEP2" and the light ring illuminates blue again.
Place the same finger gently on the sensor a second time and do not
•
remove it until the light ring goes out and you hear 1 beep.
• The display changes to „STEP3" and the light ring illuminates blue again..
• Take your finger off the sensor and place the same finger on the sensor
again a third time with gentle pressure until the display shows „GOOD" and
the ring light is illuminated with a green light and 2 beeps are heard.
The fingerprint has been successfully programmed.
If the message „FP-ERROR" appears on the display, you hear 3 short beeps and
the light ring illuminates red, the programming process has been aborted. The
entire process must be repeated. This happens, for example, if the finger on the
sensor has been placed for too long.
If you want to program additional fingerprints, start the whole process
(from programming mode) again.
Delete all stored fingerprints
• Enter the digits „33" and confirm with ENTER button.
• „GOOD" appears on the display. 2 short beeps are heard and the light ring
illuminates green.
All fingerprints have been successfully deleted.
Pure-Safe Electronic E FP