Publicidad
Idiomas disponibles
Idiomas disponibles
nOTE: The center position of the control button locks the
tool in the off position. When changing the position of the
control button, be sure the trigger is released.
nOTE: Continuous use in variable speed range is not
recommended. It may damage the switch and should
be avoided.
nOTE: The first time the tool is run after changing the
direction of rotation, you may hear a click on start up. This is
normal and does not indicate a problem.
Worklight (Fig. A)
The worklight
7
is activated when the trigger switch is
depressed, and will automatically turn off 20 seconds after
the trigger switch is released. If the trigger switch remains
depressed, the worklight will remain on.
nOTE: The worklight is for lighting the immediate work
surface and is not intended to be used as a flashlight.
Usage (Fig. A)
CAUTION: Ensure fastener and/or system will
withstand the level of torque generated by the tool.
Excessive torque may cause breakage and possible
personal injury.
1. Place the accessory on the fastener head. Keep the tool
pointed straight at the fastener.
2. Press variable speed trigger switch
Release variable speed trigger switch to stop operation.
Always check torque with a torque wrench, as the
fastening torque is affected by many factors including
the following:
‑
Voltage: Low voltage, due to a nearly discharged
battery, will reduce fastening torque.
Accessory size: Failure to use the correct accessory
‑
size will cause a reduction in fastening torque.
‑
Bolt size: Larger bolt diameters generally require
higher fastening torque. Fastening torque
will also vary according to length, grade, and
torque coefficient.
Bolt: Ensure that all threads are free of rust and other
‑
debris to allow proper fastening torque.
‑
Material: The type of material and surface finish of
the material will affect fastening torque.
Fastening time: Longer fasten ing time results in
‑
increased fastening torque. Using a longer fastening
time than recommended could cause the fasteners
to be overstressed, stripped or damaged.
specifications
Max. fastening torque
Max. breakaway torque
No load speed
Impacts per minute
Length
Weight
3
to start operation.
250 ft-lbs, 338 Nm
400 ft-lbs, 542 Nm
0-2850 rpm
0-3250 ipm
5.2" (132 mm)
2.2 lbs (1.0 kg)
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your D
WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Recommended accessories for use with your tool are available
at extra cost from your local dealer or authorized service
center. If you need assistance in locating any accessory, please
contact D
WALT call 1-800-4-D
e
visit our website: www.dewalt.com.
Impact Accessories
WARNING: Use only impact accessories. Non‑impact
accessories may break and cause a hazardous
condition. Inspect accessories prior to use to ensure
that they contain no cracks.
Repairs
The charger and battery pack are not serviceable. There are
no serviceable parts inside the charger or battery pack.
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement, when applicable) should
be performed by a D
D
WALT authorized service center. Always use identical
e
replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will help
you obtain more efficient warranty service in case there is
a problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of
an insurance loss, such as fire, flood or theft, your
English
WALT recommended
e
WALT (1‑800‑433‑9258) or
e
WALT factory service center or a
e
9
Publicidad
