Nuna Pipa lite Manual Del Usuario página 11

Product Use
Installation Concerns
DO NOT install this infant carrier on vehicle seats with Lap Belts only. (1)
This enhanced child restraint is suitable for vehicle seats with i-Size ISOFIX
anchor points with the Base. (2)
DO NOT use the rearward facing enhanced child restraint systems in
seating positions where there is an active frontal airbag installed. (3) Death
or serious injury may occur. Please reference vehicle owner's manual for
more information.
DO NOT install this enhanced child restraint on vehicle seats that face
sideways or rearward with respect to the moving direction of the vehicle.
Please refer to your vehicle owner's manual for recommended or
suggested installation positions. (4)
It is recommended to install this enhanced child restraint on the rear
vehicle seat. (5)
Handle Adjustment
1
- The infant carrier handle can be adjusted to 3 positions. (6)
2
- To adjust the handle, squeeze handle buttons on both sides. (7)-1
3
- Rotate handle until it clicks and locks into any of the 3 positions. (7)-2
An unlocked handle could move unexpectedly, causing injury to child.
Handle has to stay upright when used in the car.
Base installation
1
- Attach the ISOFIX guides to the vehicle's ISOFIX anchor bars
(see vehicle owner's manual). (8) The ISOFIX guides can protect the
surface of the vehicle seat from being torn. They can also guide the
ISOFIX connectors.
2
- Unfold the load leg from storage compartment. (9)
3
- Extend the ISOFIX connectors by pressing the ISOFIX adjustment
button while pulling on the connector. (10)
4
- Press the ISOFIX adjustment button to adjust the ISOFIX connectors.
Line up the ISOFIX connectors with the ISOFIX guides, and then "click"
both ISOFIX connectors into the ISOFIX anchor bars. (11)
Make sure that both ISOFIX connectors are securely attached to their
ISOFIX anchor bars. There should be two audible clicks and the colors
of the indicators on both ISOFIX connectors should be completely
green. (11)-1
7
PIPA lite Instructions
Check to make sure the base is securely installed by pulling on both
ISOFIX connectors.
5
- After placing the base on the vehicle seat, extend the load leg to
the floor (12). When the load leg is installed correctly, the load
leg indicator will show green. Red will be shown when installed
incorrectly. (12)-2
The load leg has multiple positions. When the load leg indicator
shows red this means the load leg is in the wrong position.
Make sure the load leg is in full contact with the vehicle floor pan.
Squeeze the load leg adjustment button, then shorten the load leg
upwards. (12)-1
The completely assembled base is shown as (13).
The ISOFIX connectors must be attached and locked onto the ISOFIX
anchor bars. (13)-1
The load leg must be installed correctly with green indicator. (13)-2
Attaching Infant Carrier to the Base
1
- Push the enhanced child restraint down onto the base (14), If the
enhanced child restraint is secure, the enhanced child restraint
indicator will show green. (15)
Check that the infant carrier is locked onto the base by pulling up on
the handle.
2
- Press the ISOFIX adjustment button and push the base back until it
comes in contact with the vehicle seat back. (16)(17)
3
- Press and hold the rotation button to rotate for easier side loading/
unloading of the child. (18)(19)(20)
4
- To release the infant carrier, squeeze the infant carrier release button
(21)-1, then lift the infant carrier up. (21)-2
Uninstalling the Base
1
- To remove the base, press the secondary lock button (22)-1 first,
followed by the button (22)-2 on the ISOFIX connectors before
removing the base from the vehicle seat. (22)
2
- For transporting, press ISOFIX Adjustment button and move the
ISOFIX connectors back into the storage position. (23)
8
PIPA lite Instructions