DeWalt DW716 Manual De Instrucciones página 8

Once made, these adjustments should remain a ccurate.
Take alittle time now tofollow these directions carefully to
maintain theaccuracy ofwhich y our s aw iscapable.
MITER SCALE A DJUSTMENT (FIG. 5 )
Place a square a gainst thesaw's f ence and blade. (Donot
touch thetipsoftheblade teeth with thesquare. Todoso
will c ause a ninaccurate measurement.) Unlock m iter l ock
lever ( J)and swing t hemiter a rm until themiter l atch locks
itatthe0 miter p osition. Donotlock miter l ock lever ( J). I f
thesawblade is notexactly p erpendicular tothefence,
loosen t hethree screws t hathold themiter s cale tothe
base andmove t hescale leftorright u ntil theblade isper-
pendicular to thefence, a s measured withthesquare.
Retighten thethree screws. Pay noattention totheread-
ingofthemiter p ointer atthis time.
MITER POINTER ADJUSTMENT (FIG. 5, 6)
To unlock, lift the miter lock lever (J) up and squeeze the
miter latch (K) to move the miter arm to the zero position.
With the miter lock lever unlocked allow the miter latch to
snap into place as you rotate the miter arm to zero.
Observe the pointer and miter scale through the viewing
opening shown in Figure 6. If the pointer does not indicate
exactly zero, loosen the screw holding the pointer in place,
reposition the pointer and tighten the screw.
BEVEL SQUARE TO TABLE (FIG. 7)
To align the blade square to the rotary table, lock the arm
in the down position. Place a square against the blade
taking care to not have the square on top of a tooth.
Loosen the bevel lock knob (L) and ensure the arm is
firmly against the 0° bevel stop. Move the 0 ° bevel stop
adjusting screw (T) as necessary so that the blade is at
zero degrees bevel to the table.
BEVEL POINTER (FIG. 7)
If the bevel pointer (M) does not indicate zero, loosen the
screw that holds it in place and move the pointer as nec-
essary. Do not remove the steel plate in front of the bevel
pointer. This plate prevents wood resin from accumulating
on the bevel scale during use.
ADJUSTING THE BEVEL STOP TO 45 ° LEFT OR
RIGHT (FIG. 8)
NOTE: Adjust the 45 ° bevel angles only after performing
the 0° bevel angle and pointer adjustment. Ensure the 45 °
bevel override levers (N) are pushed inward to obtain an
accurate adjustment.
To adjust the right 45 ° bevel angle, loosen the bevel lock
knob (L) and pull the bevel stop override knob (S) to over-
ride the 0° bevel stop. When the saw is fully to the right, if
the pointer does not indicate exactly 45 °, turn the right
bevel stop screw (O) until the pointer indicates 45 °.
To adjust the left 45 ° bevel stop, first loosen the bevel lock
FIG. 5
FIG. 6
MITER
SCALE
FIG. 7
POINTER
K
POINTER
ADJUSTMENT
SCREW
M
knob (L) and tilt the head to the left. If the pointer does not
indicate exactly 45 °, turn the left bevel stop screw until the
pointer reads 45 °.
ADJUSTING THE BEVEL STOP TO 33.85 ° (FIG. 8)
NOTE: Adjust the 33.85 ° bevel angles only after performing
the 0 ° bevel angle and pointer adjustment.
To set the 33.85 ° bevel angle, flip out the stop pawls (P).
Loosen the bevel lock knob (L) and tilt the head to the left.
If the pointer does not indicate exactly 33.85 °, turn the
screw contacting the pawl until the pointer reads 33.85 °.
To adjust the right 33.85 ° bevel angle, flip out the stop
pawl. Loosen the bevel lock knob (L) and pull the bevel
stop override button (S) to override the 0° bevel stop.
When the saw is fully to the right, if the pointer does not
indicate exactly 33.85 °, turn the screw contacting the pawl
until the pointer indicates 33.85 °.
FENCE ADJUSTMENT
Turn Off and Unplug the Miter Saw
In order that the saw can bevel to a full 48 degrees left or
right, the fences can be adjusted to provide clearance. To
adjust a fence, loosen the plastic knob (Figure 8, R), and
slide the fence outward. Make a dry run with the saw
turned off and check for clearance. Adjust the fence to be
as close to the blade as practical to provide maximum
workpiece support, without interfering with arm up and
down movement. Tighten knob securely. When the bevel
operations are complete, don't forget to relocate the fence.
NOTE: The guide groove of the fences can become
clogged with sawdust. If you notice that it is becoming
clogged, use a stick or some low pressure air to clear the
guide groove.
_ WARNING: Always use eye protection. All users and
bystanders must wear eye protection that conforms to
ANSI Z87.1. (CAN/CSA Z94.3)
AUTOMATIC ELECTRIC BRAKE
Your saw is equipped with an automatic electric blade
brake which stops the saw blade within 5 seconds of
trigger release. This is not adjustable.
On occasion, there may be a delay after trigger release to
brake engagement. On rare occasions, the brake may not
engage at all and the blade will coast to a stop.
If a delay or "skipping" occurs, turn the saw on and off 4 or
5 times. If the condition persists, have the tool serviced by
an authorized DEWALT service center.
Always be sure the blade has stopped before removing it
from the kerf. The brake is not a substitute for guards.
Ensure your own safety by giving the saw your complete
attention.