Publicidad
Idiomas disponibles
Idiomas disponibles
Carburetor Modifications for High Altitude Operation
At high altitude, the standard carburetor air-fuel mixture will be too
rich. Performance will decrease, and fuel consumption will
increase. A very rich mixture will also foul the spark plug and cause
hard starting. Operation at an altitude that differs from that at
which this engine was certified, for extended periods of time, may
increase emissions.
High altitude performance can be improved by specific
modifications to the carburetor. If you always operate your engine
at altitudes above 1,500 meters (5,000 feet), have your servicing
dealer perform this carburetor modification. This engine, when
operated at high altitude with the carburetor modifications for high
altitude use, will meet each emission standard throughout its useful
life.
Even with carburetor modification, engine horsepower will
decrease about 3.5% for each 300 meter (1,000 foot) increase in
altitude. The effect of altitude on horsepower will be greater than
this if no carburetor modification is made.
When the carburetor has been modified for high altitude operation,
the air-fuel mixture will be too lean for low altitude use. Operation
at altitudes below 1,500 meters (5,000 feet) with a modified
carburetor may cause the engine to overheat and result in serious
engine damage. For use at low altitudes, have your servicing dealer
return the carburetor to original factory specifications.
Emission Control System Information
Emission Control System Warranty
Your new Honda complies with both the U.S. EPA and State of
California emission regulations. American Honda provides the same
emission warranty coverage for Honda Power Equipment engines
sold in all 50 states. In all areas of the United States, your Honda
Power Equipment engine is designed, built, and equipped to meet
the U.S. EPA and California Air Resources Board emission standard
for spark ignited engines.
Warranty Coverage
Honda Power Equipment engines certified to CARB and EPA
regulations are covered by this warranty to be free from defects in
materials and workmanship that may keep it from meeting the
applicable EPA and CARB emissions requirements for a minimum of
2 years or the length of the Honda Power Equipment Distributor's
Limited Warranty, whichever is longer, from the original date of
delivery to the retail purchaser. This warranty is transferable to
each subsequent purchaser for the duration of the warranty period.
Warranty repairs will be made without charge for diagnosis, parts,
and labor. Information about how to make a warranty claim, as
well as a description of how a claim can be made and/or how
service can be provided, can be obtained by contacting an
authorized Honda Power Equipment dealer or by contacting
American Honda at the following:
Email: powerequipmentemissions@ahm.honda.com
Telephone: (888) 888-3139
The covered components include all components whose failure
would increase an engine's emissions of any regulated pollutant or
evaporative emissions. A list of specific components can be found
in the separately included emissions warranty statement.
Specific warranty terms, coverage, limitations and manner of
seeking warranty service are also set forth in the separately
included emissions warranty statement. In addition, the emissions
warranty statement can also be found on the Honda Power
equipment website or at the following link:
http://powerequipment.honda.com/support/warranty
Source of Emissions
The combustion process produces carbon monoxide, oxides of
nitrogen, and hydrocarbons. Control of hydrocarbons and oxides of
nitrogen are very important because, under certain conditions, they
react to form photochemical smog when subjected to sunlight.
Carbon monoxide does not react in the same way, but it is toxic.
Honda utilizes appropriate air/fuel ratios and other emissions
control systems to reduce the emissions of carbon monoxide,
oxides of nitrogen, and hydrocarbons.
Additionally, Honda fuel systems utilize components and control
technologies to reduce evaporative emissions.
The U.S., California Clean Air Act, and Environment Canada
EPA, California, and Canadian regulations require all manufacturers
to furnish written instructions describing the operation and
maintenance of emission control systems.
The following instructions and procedures must be followed in
order to keep the emissions from your Honda engine within the
emission standards.
Tampering and Altering
Tampering with or altering the emission control system may
increase emissions beyond the legal limit.
Among those acts that constitute tampering are:
• Removal or alteration of any part of the intake, fuel, or exhaust systems.
• Altering or defeating the governor linkage or speed-adjusting mechanism
to cause the engine to operate outside its design parameters.
Problems That May Affect Emissions
If you are aware of any of the following symptoms, have your
engine inspected and repaired by your servicing dealer.
• Hard starting or stalling after starting.
• Rough idle.
• Misfiring or backfiring under load.
• Afterburning (backfiring).
• Black exhaust smoke or high fuel consumption.
Replacement Parts
The emissions control systems on your new Honda engine were
designed, built, and certified to conform with EPA, California, and
Canadian emissions regulations. We recommend the use of Honda
Genuine parts whenever you have maintenance done. These
original-design replacement parts are manufactured to the same
standards as the original parts, so you can be confident of their
performance. Honda cannot deny coverage under the emission
warranty solely for the use of non-Honda replacement parts or
service performed at a location other than an authorized Honda
dealership; you may use comparable EPA certified parts, and have
service performed at non-Honda locations. However, the use of
replacement parts that are not of the original design and quality
may impair the effectiveness of your emissions control system.
A manufacturer of an aftermarket part assumes the responsibility
that the part will not adversely affect emissions performance. The
manufacturer or rebuilder of the part must certify that use of the
part will not result in a failure of the engine to comply with
emissions regulations.
ENGLISH
17
Publicidad
