First Use From New - Num'axes CANICOM 500 Manual De Instrucciones

First use from new

First use from new

 First use from new
 Fitting the battery in the receiver collar
 Fitting the battery in the receiver collar � Fitting the battery in the receiver collar
- Unscrew the 4 screws of the top of CANICOM using a screwdriver.
- Unscrew the 4 screws of the top of CANICOM using a screwdriver.
- Unscrew the 4 screws of the top of CANICOM using a screwdriver.
- Insert the battery (3V Lithium CR2) paying attention to follow polarity indicated on the battery
- Insert the battery (3V Lithium CR2) paying attention to follow polarity indicated on the battery
- Insert the battery (3V Lithium CR2) paying attention to follow polarity indicated on the battery
housing (ref. Diagram 4).
housing (ref. Diagram 4).
housing (ref. Diagram 4).
- A beep sound (low pitch) is emitted, indicating the correct installation of the battery.
- A beep sound (low pitch) is emitted, indicating the correct installation of the battery.
- A beep sound (low pitch) is emitted, indicating the correct installation of the battery.
If you do not hear any beep after having inserted the battery, remove immediately the battery from its
If you do not hear any beep after having inserted the battery, remove it immediately from its housing.
If you do not hear any beep after having inserted the battery, remove it immediately from its housing.
housing. Check the polarity before trying again
Check the polarity before trying again
Check the polarity before trying again
- Before replacing the lid, check that the rubber seal is in its groove.
- Before putting the lid back in place, check that the rubber seal is in its groove.
- Before putting the lid back in place, check that the rubber seal is in its groove.
- Screw up the 4 screws with care (do not overtighten them).
- Screw up the 4 screws with care (do not overtighten them).
- Screw up the 4 screws with care (do not overtighten them).
Polarity « - » of the battery
Diagram 4
� Activate/deactivate the remote control
 Activate/deactivate the remote control
 Activate/deactivate the remote control
Remote control is supplied with battery fitted.
Remote control is supplied with battery fitted.
Remote control is supplied with battery fitted.
- Activate: press the On/Off red button ( ) located on the side of the remote control for 1 second (ref.
- Activate: press for 1 second the On/Off red button (
- Activate: press for 1 second the On/Off red button (
Diagram.1). Indications appear on the LCD screen.
(ref. Diagram.1). Indications appear on the LCD screen.
(ref. Diagram.1). Indications appear on the LCD screen.
- Deactivate: press the On/Off red button ( ) of the remote control for 1 second (ref. Diagram.1). The
- Deactivate: press for 1 second the On/Off red button ( - Deactivate: press for 1 second the On/Off red button (
LCD screen is off.
The LCD screen is off. The LCD screen is off.
To increase the battery life of the remote control, we recommend you to deactivate the unit if you are not
To increase the battery life of the remote control, we recommend you to deactivate the unit if you are To increase the battery life of the remote control, we recommend you to deactivate the unit if you are
using your CANICOM 500 for a long period.
not using your CANICOM 500 for a long period.
not using your CANICOM 500 for a long period.
� Activate/deactivate the receiver collar
 Activate/deactivate the receiver collar  Activate/deactivate the receiver collar
A magnet located in the remote control is used to either switch on/off the receiver collar.
A magnet located in the remote control is used to either switch on/off the receiver collar. A magnet located in the remote control is used to either switch on/off the receiver collar.
Gb - 22
Gb - 22
Gb - 22
Polarity « + » of the battery
( (
( ( ( (
) located on the side of the remote control ) located on the side of the remote control
( (
( (
( (
) of the remote control (ref. Diagram.1).
) of the remote control (ref. Diagram.1).
Seal