DeWalt DCF961 Manual De Instrucciones página 28

ENglish
6. Do not freeze or immerse the charger in water or any
other liquid.
Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger from
the AC outlet before cleaning. Dirt and grease may be
removed from the exterior of the charger using a cloth
or soft non-metallic brush. Do not use water or any
cleaning solutions.
Wall Mounting
DCB107, DCB112, DCB113, DCB115, DCB118, DCB132,
DCB1106, DCB1112
These chargers are designed to be wall mountable or to sit
upright on a table or work surface. If wall mounting, locate
the charger within reach of an electrical outlet, and away
from a corner or other obstructions which may impede
air flow. Use the back of the charger as a template for the
location of the mounting screws on the wall. Mount the
charger securely using drywall screws (purchased separately)
at least 1" (25.4 mm) long, with a screw head diameter of
0.28–0.35" (7–9 mm), screwed into wood to an optimal
depth leaving approximately 7/32" (5.5 mm) of the screw
exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Anvil (Fig. C)

WARNING: Use only impact accessories. Non-impact
accessories may break and cause a hazardous
condition. Inspect accessories prior to use to ensure that
it con tains no cracks.

CAUTION: Inspect anvils and hog rings prior to
use. Missing or damaged items should be replaced
before use.
Place the switch in the locked off (center) position or remove
battery pack before changing accessories.
To install an accessory on the hog ring anvil, firmly push
3
accessory onto the anvil
to allow the accessory to slide on. After accessory is
installed, the hog ring applies pressure to help provide
accessory retention.
To remove an accessory, grasp the accessory and firmly
pull it off.
Mode Selector (Fig. A, D)
Your tool is equipped with a mode selector
you to select one of three speeds or Precision Wrench™
mode. Select the mode based on the maximum speed/
torque needed and control the speed of the tool using the
variable speed trigger switch
26
10
. The hog ring compresses
9
which allows
1
.
Precision Wrench™ (Fig. D)
In addition to normal impacting modes, this tool features
the Precision Wrench™ mode which grants the user greater
control in both fastening and loosening applications.
When set in forward, the tool will fasten at 1200 RPM until
impact begins. The tool will then pause for 0.75 seconds
before continuing to impact at a rate of 1890 IPM, providing
the user with greater control and reducing the chance of
overtightening or damaging material.
When set in reverse, the tool will impact at a normal speed
and rate of 1890 IPM. Upon sensing that the fastener has
broken free, the tool will cease to impact and will reduce
speed to help prevent "run‑off" of loose hardware.
specifications
Mode
Precision Wrench™ Mode
Low Mode
Medium Mode
High Mode*
*After 4 seconds of impacting, the DCF961 automatically increases power to
aid in loosening stubborn fasteners.
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Installing and Removing the Battery Pack
(Fig. H)

WARNING: Ensure the tool/appliance is in the off
position before inserting the battery pack.
NoTE: For best results, make sure your battery pack is
fully charged.
1. To install the battery pack
the battery pack with the rails inside the tool's handle
and slide it into the handle until the battery pack is firmly
seated in the tool and ensure that it does not disengage.
2. To remove the battery pack from the tool, press the
battery pack release button
pack out of the tool handle. Insert it into the charger as
described in the charger section of this manual.
Proper Hand Position (Fig. F)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
4
handle .
Application
Precision Wrench™ 0–1200 forward
0–550 reverse
Normal Impacting 0–440 forward
0–1200 reverse
Medium Impacting 0–800 forward
0–1200 reverse
High Speed Impacting 0–1200 forward
0–1200 reverse
6
into the tool handle, align
5
and firmly pull the battery
RPM