Publicidad
Idiomas disponibles
Idiomas disponibles
Al EDIT RECORDING
3,7.-
4
5-
3,7
~
The Al edit function
enables
CD recording
without worrying
about
tape length
and track length.
When
a CD is inserted,
the unit
automatically
calculates
the total track length.
If necessary,
the
order of tracks is rearranged
so that no track is cut short.
(Al: Artificial
Intelligence)
m
Al edit recording
will not-start from a point halfway
into the tape.
The tape must be recorded
from the beginning
of either side.
7 Insert
the tape into deck 2.
Insert the tape with the side to be recorded
on first facing out
from the unit.
2
Press
the
CD
button
and load the disc(s).
3 Press the
EDIT/CHECK
button
once
while
pressing the SHIFT button on the remote control:
"EDIT" and "Al" light upon
the display.
Each time it is pressed,
the display
changes
as follows.
Al EDIT —
PRGM EDIT
~
Press one of the DISC DIRECT PLAY buttons to
select a disc.
5 Press
the numbered
buttons
on the remote
control to designate
the tape length.
10 to 99 minutes
can be specified.
Example:
When
using a 60-minute
tape, press the 6 and O
buttons.
In a few seconds,
the microcomputer
programes
the tracks
to be recorded
on each side of the tape.
The <
and -
buttons
are also available
to designate
the tape length.
Tape side A
Programmed
Tape length
(front side)
tracks for side A
I
Remaining
time of side A
15
ENGLISH
6
7
8
Press the
REC/REC
MUTE
button
to start
.
recording
on the first side.
The tape is rewound
to the beginning
of the first side, the
lead segment
is played through for 10 seconds,
and recording
starts. When the last track programmed
for side A is finished,
deck 2 enters
the recording
stop mode.
After
entering
the
recording
stop mode, go to step 7.
Press the"EDIT/CHECK
button while pressing the
SHIFT button on the remote control to display
the program for the second recording.
"B" is displayed.
.
Turn over the tape in deck 2 and press the
REC/REC MUTE button to start recording on the
second side.
To
stop recording
Press the
button. Recording
and CD play stop simultaneously.
To clear the edit
program
Press the
CLEAR
button twice so that "EDIT
disappears
on
the display.
To
check the order of the programmed
track numbers
Before
recording,
press the EDIT/CHECK
while
pressing
the
SHIFT
button
on the remote
control
to select
side A or B, and
press the -
or E
button
repeatedly.
Programmed
Track number
track numbers
1
Program
number
To
add tracks from other discs to the edit program
If there is any time remaining
on the tape after step 5, you can
add tracks from other discs in the CD compartment
1
Press
the EDIT/CHECK
button
while
pressing
the SHIFT
button on the remote
control to select side A or B.
2
Press one of the DISC DIRECT
PLAY buttons to select a disc.
3
Press the numbered
buttons
on the remote
control
to select
tracks. "PRGM"
appears
on the display.
A track whose playing time is longer than the remaining
time
cannot
be programmed.
4
Repeat
steps 2 and 3 to add more tracks.
Time on cassette tapes and editing time
The
actual cassette
recording
time is usually
a little longer than
the specified
recording
time printed
on the label.
This unit can
program
tracks to use the extra time.
When the total recording
time is a little longer
than the tape's
specified
recording
time
after editing,
the display
shows the extra time (without
a minus
mark), instead
of the time remaining
on the tape (with the minus
mark).
m
The Al edit function
cannot
be used with discs containing
31
tracks or more.
Publicidad
